Offer List

        Description: Feeding feature by PLC program from MITSUBISHI 1) NC Servo feeding. Operating with computerized numerical control by PLC program from MITSUBISHI made in Japan. The electrical parts from YASKAWA made in Japan including Servo motor, driver, encoder, interface screen and so on 2) High precision feeding: meet the coming of hi-tech industry needs, controlled by computer closed circuit feedback system to keep precision degree within +/-0.03mm 3) Feeding function: input 20 sets of different feeding length, each group provides 999 times for punching or cutting to satisfy processing of special products 3) High efficiency release device, match with adjustment of signal from the cutter or press machine through cable wire 4) Setting of feeding length: directly input feeding length on the control screen , and then it can reach needed distance, feed length max. 9999.99mm, speed max. 40m/min press features: The body of JH21 series press is welded with steel plate,so it is with good rigidity and stable precision.The crankshaft is placed lengthways,so the structure is compact and the contour beautiful. Using the combined pneumatic friction clutch and brake,so the engagement is smooth,the action agile,and the noise low.Gear pair adopts the flooding system lubrication.The slide block is six-face rectangle with longer guide track whose face is bronze panel.Meanwhile an import hydraulic overload protector is installed in the slideblock whose air pump and high pressure ring seal are imported from other country.Its action is agile and reliable.The die set is adjusted by motor over JH21-63 press.There set lifting balance cylinder at the slideblock over model JH2I-4O press,whose ring seal is imported from other country.The air pipeline is controlled by safety duplex valve. Its electric circuit is controled by import PLC.The press can be equipped with air cushion, automatic feed shaft and photoelectric protector,and can be equipped with various automatic equipment which conform to the safety standard of press. Straightening Features 1.The unique openable bias rolls design. 2.the whole upper rollers can be opened 3.easy loading, feeding, cleaning and operation 4.The upper work rollers adop 4 point fine micro adjusters with reading 0.01 mm advance reference indicators, high quality and precision. 5.All rolls are made of bearing steel (SUJ2), have all been quenched, hard chrome plated and ground with min. HRC 60 . 7.Outgoing cantenary assist and support the material.

        General Introduction this line is used in decoiling, straightening and shearing different specification coils into flat steel plate with different width and length, and then stacking the flat steel plate. this production line which is high automatization and simple operation can process all kinds of cold or hot rolling carbon steel, galvanized plate, aluminum plate, stainless steel etc. it is widely used in auto, container,homeelectricity,food-packing,architecture,ship-building, boiler-making and so on.

        1) Models: KJC 2) Material width (mm): 1000/1250/1,300 / 1,600 / 2,000 3) Material thickness (mm): 0.6 - 6.0mm 4) Coil load (kg): 2,000 / 3,000 / 7,000 / 10,000kg 5) Coil inner diameter (mm): 508 6) Coil outer diameter (mm): 1,200 7) Speed (m/min): 15-20 8) Straightening precision 9) Coil expansion: hydraulic 10) Gauge precision: +/-1.0 11) Power motor (kW): 100 12) Coil car: optional 13) Air hold down arm: stander I. General Induction. Cut To Length Lines can do uncoiling, straightening, gauging, cross-cutting to length and stacking work. It mainly includes uncoiler, straightener, gauge, shearer, conveyor, stacker, hydraulic system, pneumatic system and electrical system, etc., the line can make sure of accurate feeding and shearing. It can be widely used in cold or hot rolling carbon steel, tinplate, stainless steel and all the other kinds of metal materials with surface coating. Cut to length line is controlled by PLC system. It has CNC controlled single shaft feeder, The information of length, shearing numbers and speed can be input to the CNC systems. When the need shearing number is reached the line can stop automatically. The line speed can be adjusted, It has a gauge with high precision, and whole line can work automatically and operate easily, smooth sheet can be made.

        Technical data Model: KJS -0.5 x 1300 to KJS-14 x 2000 Coil thickness: 0.15 to 0.5, 0.25 to 1.5 and 4 to 14mm Coil width: 500 to 1,300, 100 to 300 and 900 to 2,000mm Width: +/-0.05 to +/-0.5mm Slitting speed: 50 to 120, 50 to 160, 30 to 80 and 8 to 20m/min This production is used to let the steel coil to uncoiler, section shear and recoiler This line is fit to machining cold carbon roll steel and hot carbon roll sheet, tin stainless steel and many metal plated coil Production line includes uncoiler car, uncoiler, leveler, section shear, waste coil recoiler, pinch machine, recoiler and unloading set Whole line is controlled by PLC, human and machine screen display, high automatic degree, to control is simple and good

        1) High speed SPM 600 2) Easily adjustable for different thickness and width 3) Practical and economical with simple mechanism 4) Easy maintained with less trouble Feed accuracy: Depends on feed length of stock and stroke of press, the general accuracy is within ±0.05mm, and can be better up to ±0.01mm by pilot pin with automatic stop system. Single type: 1) For cutting stock at certain length or coiling back the finished products 2) Double type: for there is any stuff left after stamping and for short or thin stock Mechanical features: 1) One way clutch: a) Made of tungsten carbide steel on the contacting surface to keep rigidity, precision, and durability b) The gear has high precision transmission after HRC 60 degrees heat treatment and precisely grinding 2) Roller: a) High feed accuracy at exact positioning with hollow roller of less eight, and lower inertia b) Hard chrome plated heat treated to HRC60 degree and ground for the best rigidity and durability 3) The anti-reversing device: a) The structure is same the one way clutch, It can precisely control the lower roller which will not reverse even for long time used as it is high in stability and precision b) The brake will not out of control by the splashed waste oil when it is punching such cause the lower roller to reverse, and transfer distance imprecision c) It will not cause high heat d) Super hard alloy and rolling post have been used. they are not easy to wear out e) The acting form of the rolling post is by circular movement, not like the four guided posts in straight line moving, so it will not stuck f) As less friction it will accrued, so the torsion it need will correspondingly reduced. The transfer structure will not easy wear out g) Speed can be reach to 30M/ min if the reversing device is fitted. In general, it is 20M/min. Efficiency has been increase about 50% h) Customers are welcomed to place orders for special specifications

        I. General Induction. Cut To Length Lines can do uncoiling, straightening, gauging, cross-cutting to length and stacking work. It mainly includes uncoiler, straightener, gauge, shearer, conveyor, stacker, hydraulic system, pneumatic system and electrical system, etc., the line can make sure of accurate feeding and shearing. It can be widely used in cold or hot rolling carbon steel, tinplate, stainless steel and all the other kinds of metal materials with surface coating. Cut to length line is controlled by PLC system. It has CNC controlled single shaft feeder, The information of length, shearing numbers and speed can be input to the CNC systems. When the need shearing number is reached the line can stop automatically. The line speed can be adjusted, It has a gauge with high precision, and whole line can work automatically and operate easily, smooth sheet can be made. II. machine components in the cut to length line 1.coil car 2.decoiler 3.entry support device 4.width adjustor device 5.straightening machine 6.gauge table 7.shearing machine 8.run off table 9.pneumatic discharge and stacker device 10.unloading table 11.pueumatic system 12.Electrical system with computer PLC program control 13.Hydraulic system

        I. General Induction. Cut To Length Lines can do uncoiling, straightening, gauging, cross-cutting to lengt and stacking work. It mainly includes uncoiler, straightener, gauge, shearer, conveyor, stacker, hydraulic system, pneumatic system and electrical system, etc., the line can make sure of accurate feeding and shearing. It can be widely used in cold or hot rolling carbon steel, tinplate, stainless steel and all the other kinds of metal materials with surface coating.Cut to length line is controlled by PLC system. It has CNC controlled single shaft feeder, The information of length, shearing numbers and speed can be input to the CNC systems. When the need shearing number is reached the line can stop automatically. The line speed can be adjusted, It has a gauge with high precision, and whole line can work automatically and operate easily, smooth sheet can be made.II. machine components in the cut to length line1. coil car 2. decoiler3. entry support device 4. width adjustor device 5. straightening machine 6. gauge table7. shearing mahine 8. run off table9. pneumatic discharge and stacker device10.unloading table11. pneumatic system12. Electrical system with computer PLC program control. 13. Hydraulic system

        Description: Technical parameter: 1. Manual decoiler: passive decoil , manual expansion 2. Loading weight of decoiler:5 Tons 3. main power:5.5KW 4. roller station:34 stands 5. shaft of roller:80mm (heating process) 6. Motor power of hydraulic station: 2.2 KW 7. oil pump of hydraulic station(gear pump):CB-E310 8. the material of blade: Cr12 9. heating process of cutting blade: HRC600-620 9. forming thickness: 1.0-1.5mm 10. length tolerance: 10¡À1.5mm 11. The single surface of roller is coated with chrome with 0.05 mm 12. Frequency converter 13. The computer adopts PLC control, Mitsubishi 14. The operating broad adopts TD200 Siemens

        Description: Technical parameter: 1. Manual decoiler : Non-motorize, manual expansion 2. Loading weight of decoiler: 5 Tons 3. main power: 22KW 4. roller station: 33 stands 5. shaft of roller: 80mm (heating process) 6. Motor power of hydraulic station: 5.5 KW 7. oil pump of hydraulic station(gear pump): CB-E310 8. the material of blade: Cr12 9. heating process of cutting blade:HRC600-620 10. forming thickness: 0.8-1.2mm 11. Width: 1000mm 12.length tolerance: 10¡À1.5mm 13. The single surface of roller is coated with chrome with 0.05 mm 14. Frequency converter 15. The computer adopts PLC control. 16. The operating broad adopts from Mitsubishi

        Description: 1. Suitable for processing of large sizes materials 2 Use magnetic valve operation (electric control is also available), use microswitch control 3. Flexible horse, match with punch and cutting height, change the material at random 4. Simple installation, safe and easy operation, small failure rate, precise feeding 5. The picture on the left is 8C; air reservoir is matched above

        Specification List Specification UF-800 UF-1000 UF-1200 UF-1500 Width 120 120 150 150 Load Weight 1000 1500 2000 2000 Thickness 1.2 1.2 1.2 1.2 Load Height 600 600 600 600 Roll Diameter 800 1000 1200 1500 Delivery Speed 0-24 0-24 0-24 0-24 Motor 1/2 1 1 2 Machine Weight 250 300 350 400 Dimension (mm) 850 1050 1250 1550 750 950 1150 1450 500 500 500 500 380 380 380 380 1250 1450 1600 1900 1560 1560 1560 1560

        1) High speed SPM 600 2) Easily adjustable for different thickness and width 3) Practical and economical with simple mechanism 4) Easy maintained with less trouble Feed accuracy: Depends on feed length of stock and stroke of press, the general accuracy is within ±0.05mm, and can be better up to ±0.01mm by pilot pin with automatic stop system. Single type: 1) For cutting stock at certain length or coiling back the finished products 2) Double type: for there is any stuff left after stamping and for short or thin stock Mechanical features: 1) One way clutch: a) Made of tungsten carbide steel on the contacting surface to keep rigidity, precision, and durability b) The gear has high precision transmission after HRC 60 degrees heat treatment and precisely grinding 2) Roller: a) High feed accuracy at exact positioning with hollow roller of less eight, and lower inertia b) Hard chrome plated heat treated to HRC60 degree and ground for the best rigidity and durability 3) The anti-reversing device: a) The structure is same the one way clutch, It can precisely control the lower roller which will not reverse even for long time used as it is high in stability and precision b) The brake will not out of control by the splashed waste oil when it is punching such cause the lower roller to reverse, and transfer distance imprecision c) It will not cause high heat d) Super hard alloy and rolling post have been used. they are not easy to wear out e) The acting form of the rolling post is by circular movement, not like the four guided posts in straight line moving, so it will not stuck f) As less friction it will accrued, so the torsion it need will correspondingly reduced. The transfer structure will not easy wear out g) Speed can be reach to 30M/ min if the reversing device is fitted. In general, it is 20M/min. Efficiency has been increase about 50% h) Customers are welcomed to place orders for special specifications

        Technical data Model: KJS -0.5 x 1300 to KJS-14 x 2000 Coil thickness: 0.15 to 0.5, 0.25 to 1.5 and 4 to 14mm Coil width: 500 to 1,300, 100 to 300 and 900 to 2,000mm Width: +/-0.05 to +/-0.5mm Slitting speed: 50 to 120, 50 to 160, 30 to 80 and 8 to 20m/min This production is used to let the steel coil to uncoiler, section shear and recoiler This line is fit to machining cold carbon roll steel and hot carbon roll sheet, tin stainless steel and many metal plated coil Production line includes uncoiler car, uncoiler, leveler, section shear, waste coil recoiler, pinch machine, recoiler and unloading set Whole line is controlled by PLC, human and machine screen display, high automatic degree, to control is simple and good

        Description: Feeding feature by PLC program from MITSUBISHI 1) NC Servo feeding. Operating with computerized numerical control by PLC program from MITSUBISHI made in Japan. The electrical parts from YASKAWA made in Japan including Servo motor, driver, encoder, interface screen and so on 2) High precision feeding: meet the coming of hi-tech industry needs, controlled by computer closed circuit feedback system to keep precision degree within +/-0.03mm 3) Feeding function: input 20 sets of different feeding length, each group provides 999 times for punching or cutting to satisfy processing of special products 3) High efficiency release device, match with adjustment of signal from the cutter or press machine through cable wire 4) Setting of feeding length: directly input feeding length on the control screen , and then it can reach needed distance, feed length max. 9999.99mm, speed max. 40m/min press features: The body of JH21 series press is welded with steel plate,so it is with good rigidity and stable precision.The crankshaft is placed lengthways,so the structure is compact and the contour beautiful. Using the combined pneumatic friction clutch and brake,so the engagement is smooth,the action agile,and the noise low.Gear pair adopts the flooding system lubrication.The slide block is six-face rectangle with longer guide track whose face is bronze panel.Meanwhile an import hydraulic overload protector is installed in the slideblock whose air pump and high pressure ring seal are imported from other country.Its action is agile and reliable.The die set is adjusted by motor over JH21-63 press.There set lifting balance cylinder at the slideblock over model JH2I-4O press,whose ring seal is imported from other country.The air pipeline is controlled by safety duplex valve. Its electric circuit is controled by import PLC.The press can be equipped with air cushion, automatic feed shaft and photoelectric protector,and can be equipped with various automatic equipment which conform to the safety standard of press. Straightening Features 1.The unique openable bias rolls design. 2.the whole upper rollers can be opened 3.easy loading, feeding, cleaning and operation 4.The upper work rollers adop 4 point fine micro adjusters with reading 0.01 mm advance reference indicators, high quality and precision. 5.All rolls are made of bearing steel (SUJ2), have all been quenched, hard chrome plated and ground with min. HRC 60 . 7.Outgoing cantenary assist and support the material.

        1) The machine is equipped with DRO (digital readout) system to display the values of ram and back gauge, (ball screws), and the side and back guard 2) NC or CNC can be attached to the machine 3) Back gauge (ball screw) 4) Hydraulic elements, Atos (Italy) 5) Electrical elements, Siemens (Germany) 6) Guarantee: 12 months from the date of B/L

        I. General Induction. Cut to length line is used in decoiling, straightening and shearing different specification coils into flat steel plate with different width and length, and then stacking the flat steel plate. this production line which is high automatization and simple operation can process all kinds of cold or hot rolling carbon steel, galvanized plate, aluminum plate, stainless steel etc. it is widely used in auto, container,homeelectricity,food packing,architecture,ship-building,boiler-making and so on. II.Machine Structure and Technical Description This line with hydraulic, pneumatic, electromotion, mechanical and electric control is automation production line. III.Machine components in this production line as follow: 1.hydraulic coil car 2.hydraulic decoiler 3.hydraulic hold down device 4.limited space worktable 5.straightening main machine 6.fixing ruler worktable 7.shearing mahine 8.feeding worktable 9.pneumatic discharge rack 10.Hydraulic automatic lifter table 11.discharge worktable 12.hydraulic pneumatic system 13.Electrical control system.