Switch and Jack,TRIMMING

  General specification: Scope: this specification covers the requirements for single key switches which have no key top Operating temperature range: -20-70 degree Celsius Storage temperature range: -20-80 degree Celsius Actuating force: 100-260 +/-30gf Travel: 0.3+/-0.1mm Stem strength: 3kg Contact resistance: 50m ohms maximum Insulation resistance: 100m ohms maximum Dielectric with standing: there shall be no breakdown

  Electrical characteristics: Rated power: DC 12V, 1A Contact resistance: measurement shall be made at with small current 1,000Hz(1A maximum) Insulation resistance: a voltage of 500V DC shall be applied for 1 minute after which measurement shall be made Dielectric strength: 500V AC(50Hz-60Hz) for 1 minute Trip current: 2mA Endurance characteristics: Soldering heat test: the terminal for a printed circuit board Temperature of solder: 260+/- Dip time: 5±1 seconds The terminal for a lead wire: Temperature of solder: 350±10 Dip time: 3±1 seconds Cold: the jack shall be stored for 96 hours at a temperature of -25±3 immediately after which measurement shall be made Dry heat: the jack shall be stored for 96 hours at a temperature of 70±2 immediately after which measurement shall be made Contact resistance: 50m ohms maximum Insulation resistance: 50m ohms minimum Contact pressure: 0.5N(50gf) minutes Insertion force: 3-30N(0.3-3.0kgf) Withdrawal force: 3-30N(0.3-3.0kgf)

  Electronics characteristics: Rating: DC 12V, 1A Contact resistance: 1kHz measured at small current (1A or less) Insulation resistance: a voltage of 500V DC shall be applied for a minute, between conductors which should not make contact under normal conditions after which measurement shall be made Dielectric strength: between conductors which should not make contact under normal conditions. 500V AC (50 to 60Hz) for 1 minimum (trip current 2mA) Endurance characteristics: Solderability: the terminals shall be dipped into soldering flux, and shall be immersed into molten solder of 230 degrees +/- 5 degrees for a period 3+/-0.5 seconds Resistance to soldering heat: Solder temperature: 350 degrees C +/- 10 degrees C Immersion depth: 2+/-0.5mm Immersion time: 3+/-0.5 seconds By a solder iron to have capacity of 60W Cold: the jack shall be stored at a temperature of -40 degrees C +/- 2 degrees C for 96 hours. And then it shall be subjected to the controlled recovery conditions for 0.5 hours after which measurement shall be made Dry Heat: the jack shall be stored at a temperature of -70 degrees C +/- 2 degrees C for 96 hours. And then it shall be subjected to the controlled recovery conditions for 0.5 hours after which measurement shall be made Humidity: the pin jack shall be subject to 90% to 95%RH, 40 degrees C +/- 2 degrees C for 96 hours, and shall be conditioned at room ambient conditions for a period of 30 minutes

  Electrical characteristics: Rated power: DC 12V, 1A Contact resistance: measurement shall be made at with small current 1000Hz(1A maximum) Insulation resistance: a voltage of 500V DC shall be applied for 1 minute after which measurement shall be made Dielectric strength: 500V AC(50Hz-60Hz) for 1 minute Trip current: 2mA Endurance characteristics: Soldering heat test: the terminal for a printed circuit board Temperature of solder: 260+/- Dip time: 5±1 seconds The terminal for a lead wire: Temperature of solder: 350±10 Dip time: 3±1 seconds Cold: the jack shall be stored for 96 hours at a temperature of -25±3 immediately after which measurement shall be made Dry heat: the jack shall be stored for 96 hours at a temperature of 70±2 immediately after which measurement shall be made Contact resistance: 50m ohms maximum Insulation resistance: 50m ohms minimum Contact pressure: 0.5N(50gf) minutes Insertion force: 3-30N(0.3-3.0kgf) Withdrawal force: 3-30N(0.3-3.0kgf)

  Electrical characteristics: Rated power: DC 12V, 1A Contact resistance: measurement shall be made at with small current 1,000Hz(1A maximum) Insulation resistance: a voltage of 500V DC shall be applied for 1 minute after which measurement shall be made Dielectric strength: 500V AC(50Hz-60Hz) for 1 minute Trip current: 2mA Endurance characteristics: Soldering heat test: the terminal for a printed circuit board Temperature of solder: 260+/- Dip time: 5±1 seconds The terminal for a lead wire: Temperature of solder: 350±10 Dip time: 3±1 seconds Cold: the jack shall be stored for 96 hours at a temperature of -25±3 immediately after which measurement shall be made Dry heat: the jack shall be stored for 96 hours at a temperature of 70±2 immediately after which measurement shall be made Contact resistance: 50m ohms maximum Insulation resistance: 50m ohms minimum Contact pressure: 0.5N(50gf) minutes Insertion force: 3-30N(0.3-3.0kgf) Withdrawal force: 3-30N(0.3-3.0kgf)

  Characteristics: Range of nominal resistance: 10 Ohms to 2M Ohms Resistance tolerance: ±10% Terminal resistance: 1%R or 2 Ohms Contact resistance variation: 3%R or 3 Ohms Insulation resistance: R1≥1G Ohms Withstand voltage: 101.3kPa/500V, 8.5kpa/315V Effective electrical travel: 210±100 Rated maximum power working voltage: 250V +70V 0.5W +125W Temperature range: -55 to +125 degrees Celcius TCR: ±250ppm Temperature variation: R≤±2%RUab/UacR≤±1% Collision: 390m/s2, 4000uqw, R≤≥1%R Vibration: 10 to 2,000Hz, 0.75mm, 98m/s2, 6h R≤±1%RUab/Uac≤±2% Climate category: R≤±3%RR1≥100M Electrical endurance: 70W, 0.5W, 1,000h, R≤±3%R Mechanical endurance: 100cycles, R≤±3%R Steady damp-heat R≤≥3%R, R1≥100M Total mechanical travel: 2500±100 Starting torque: ≤20mNm Stop torque: ≥50mN?m Standard packaging: 50 pieces per tube

  Characteristics: Range of nominal resistance: 10 Ohms to 2M Ohms Resistance tolerance: ±10% Terminal resistance: 1%R or 2 Ohms Contact resistance variation: 3%R or 3 Ohms Insulation resistance: R1≥1G Ohms Withstand voltage: 101.3kPa/500V, 8.5kpa/315V Effective electrical travel: 210±100 Rated maximum power working voltage: 250V +70V 0.5W +125W Temperature range: -55 to +125 degrees Celcius TCR: ±250ppm Temperature variation: R≤±2%RUab/UacR≤±1% Collision: 390m/s2, 4000uqw, R≤≥1%R Vibration: 10 to 2000Hz, 0.75mm, 98m/s2, 6h R≤±1%RUab/Uac≤±2% Climate category: R≤±3%RR1≥100M Electrical endurance: 70W, 0.5W, 1,000h, R≤±3%R Mechanical endurance: 100cycles, R≤±3%R Steady damp-heat R≤≥3%R, R1≥100M Total mechanical travel: 2500±100 Starting torque: ≤20mNm Stop torque: ≥50mN?m Standard packaging: 50 pieces per tube

  Electronical characteristics: Range of nominal resistance: 10-2 mega Ohms Resistance tolerance: 10 percent Terminal resistance: 1percent R or 2 Ohms Contact resistance variation: 3 percent R or 3 Ohms Insulation resistance: R1 1Giga Ohms Withstand voltage: 101.3 kPa, 500V, 8.5kpa, 315V Effective electrical travel: 210±100 Environment characteristics:Power voltage: 250V +70 0.5W+125 0W Temperature range: -55 - +125 degree celsius TCR: 250ppm Temperature variation: R 2 percentR Uab/UacR 1 percent Collision: 390m/s2,4000uqw, R 1percentR Vibration: 10-2,000Hz 0.75mm 98m/s26h Climate category: R3RR1 100M Electrical endurance: 70ohms 0.5W1000h R 3percent R Mechanical endurance: 100 cycles R3R Steady damp-heat

  Characteristics: Range of nominal resistance: 10 Ohms to 2M Ohms Resistance tolerance: ±10% Terminal resistance: 1%R or 2 Ohms Contact resistance variation: 3%R or 3 Ohms Insulation resistance: R1≥1G Ohms Withstand voltage: 101.3kPa/500V, 8.5kpa/315V Effective electrical travel: 210±100 Rated maximum power working voltage: 250V +70V 0.5W +125W Temperature range: -55 to +125 degrees Celcius TCR: ±250ppm Temperature variation: R≤±2%RUab/UacR≤±1% Collision: 390m/s2, 4000uqw, R≤≥1%R Vibration: 10 to 2000Hz, 0.75mm, 98m/s2, 6h R≤±1%RUab/Uac≤±2% Climate category: R≤±3%RR1≥100M Electrical endurance: 70W, 0.5W, 1,000h, R≤±3%R Mechanical endurance: 100cycles, R≤±3%R Steady damp-heat R≤≥3%R, R1≥100M Total mechanical travel: 2500±100 Starting torque: ≤20mNm Stop torque: ≥50mN?m Standard packaging: 50 pieces per tube

  Mechanical characteristic Total rotation angle: 230 ± 10deg Rotation torque: 40-250GF.CM Stopper strength: ≥1 kgf.cm Electrical characteristic Total resistance range: 100-2mOhm Total resistance tolerance: 500Ohm＜R＜1MOhm, ±20%, other：±30% Resistance taper: linear (B) Power rating (70deg. C): 0.1W Max. operation voltage: 100 VDC Rotaion noise: ≤100MV Residual resistance: ≤1％ or 100Ohm Max Endurance Rotation life: 100 cycles R＜10% R Temperature: 20-70deg. C R＜±8%R Moisture: 40deg.C 95% 5 hours(R/R) R≤±15％ Load: 40deg. C 95% 5 hours (R/R) R≤±15% Soldering heat: soldering should be carried out within 3 seconds at a temperature of 270℃ max

  Electrical characteristics: Total resistance: 100-5MΩ Total resistance tolerance: ±20Ω Ratings power: 0.1W Resistance taper: taper B Sliding noise: 150mV maximum Taper: curve Maximum power rating: 0.5W Maximum working voltage: 250V Mechanical characteristics: Rotation angle: 260±10 degrees Rotation torque: 5-35Nm Stopper strength: ≥100Nm Working temperature: 40 - 125 degree Celsius Terminal strength: 30Nm

  Electrical characteristics Total resistance: 100 ~ 1MΩ Total resistance tolerance: ±30Ω Ratings power: 0.1W Resistance taper: taper B Sliding noise: 150mV maximum Temperature characteristics: ±15% maximum Insulation resistance: 100MΩ, minimum at DC 100V Maximum operating voltage: AC100V at 50 degree Celsius Solder heat resistance: 240 ~ 280 degree Celsius for 5s or 280 ~ 300 degree Celsius for 3s Operation torque: 40~350gf/cm Rotation stopper strength: 0.5kgf/cm/min Total rotational angle: 260±10° Endurance characteristics Rotational life: more than 100 turns

   Mechanical characteristic Total rotational angle: 200 +/- 20 degrees Rotational torque: 60-150gf.Cm Stopper strength: 500g.Cm minimum Electrical characteristic Total resistance range: 100 - 2.2mΩ Resistance taper: linear (b) Power rating: ≤0.1W Maximum operating voltage: 50V DC Soldering heat characteristic: soldering should be carried out within 2sec a maximum temperature of 250 degree Celsius

  Mechanical characteristic Total rotational angle: 200 +/- 20deg Rotational torque: 60-150gf. Cm Stopper strength: 500g. Cm minimum Electrical characteristic Total resistance range: 100w-2.2mw Resistance taper: Linear (b) Power rating(70'c): ≤ 0.1w Soldering heat characteristic: Soldering should be carried out within 2 seconds at a temperature of 250deg. C max

  Resistance value and tolerance: 100 to 2.2MΩ, ±20% Taper: curve Maximum power rating: 0.3W at 70 degree Celsius Maximum working voltage: 250V Sliding noise: 5% Residual resistance: 10 ohms, R≤1K ohms, 1% Mechanical characteristics: Rotation angle: 240 ±10 degrees Rotation torque: 3 to 30mN.m Stopper strength: ≥50mN.m Reliability specifications: Operating life: 30 ±10% 30 cycle resistance value: ±10％ Temperature coefficient: ±3%,70°C 5HR 3%, 70°C 5HR Temperature coefficient: ±250m/°C Humidity characteristic: ±5%, 40°C, 90 to 95%RH, without load ±7 Resistance to soldering heat: pass 350%, 3 seconds or 260% 10 seconds, without any poor contact Working temperature: -40 to 125% Terminal strength: 30N.m Temperature cycle: Without load: 25 to 40°C, ±5% With load: 25 to 125 degrees Celsius, ±7%

  Characteristics: Range of nominal resistance: 10 to 2 M Ohms Resistance tolerance: ±10% Terminal resistance: 1% R or 2 Ohms Contact resistance variation: 3% R or 3 Ohms Insulation resistance: R1≥ 1G Ohms Withstand voltage: 101.3kPa 500V, 8.5kpa 315V Effective electrical travel: 210±100 Rated maximum power working voltage: 250V +70V 0.5W +125W Temperature range: -55 to +125 degree Celsius TCR: ±250ppm Temperature variation: R≤± 2% RUab/UacR≤ ±1% Collision: 390m/s2,2400uqw, R≤≥1%R Vibration: 10 to 2000Hz, 0.75mm, 98m/s2, 6h R≤± 1%RUab/Uac≤±2% Climate category: R≤ ± 3% RR1≥ 100M Electrical endurance: 70W, 0.5W, 1000h, R≤±3%R Mechanical endurance: 100 cycles, R≤± 3%R steady damp-heat R≤≥3%R, R1≥100M Total mechanical travel: 2500±100 Starting torque: ≤20mNm Stop torque: ≥50mN?m Standard packaging: 50 pieces per tube

  Nominal resistance: 10 to 2M Resistance tolerance: 10% Terminal resistance: 1 percent or 2 Contact resistance variation: 3 percentR or 3 Insulation resistance: R1 1G Withstand voltage: 101.3 kPa 500V, 8.5kpa315V Effective electrical travel: 210 +- 100 Power working voltage: 250V +70 0.5W +125 0W Temperature range: -55 to +125 degrees Celsius TCR: 250ppm Temperature variation: R2 percent R Uab/Uac R1 percent Collision: 390m/s2,4000uqw, R1 percent R Vibration: 10~2000Hz0.75mm 98m/s2 Climate category: R3 percentR R1 100M Electrical endurance: 70 0.5W 1000h R 3R Mechanical endurance: 100 cycles R 3R Steady damp-heat: R3 percent R R1 100M Physical charactiristics: Total mechanical travel: 210 10 Starting torque: 20mNm Stop torque: 50mNm Standard packaging: 50pcs per tube

  Range of nominal resistance: 10 to 2Mohms Resistance tolerance: ±10% Terminal resistance: 2 ohms Contact resistance variation: 3 ohms Insulation resistance: R1 ≥1G ohms Withstanding voltage: 101.3kPa, 500V and 8.5kPa, 315V Effective electrical travel: 210 ±100 degrees Rated power: maximum working voltage 250V, +70 degrees Celsius, 0.5W and +125 degrees Celsius Temperature range: -55 to +125 degrees Celsius TCR: ±250ppm/°C Temperature variation: ΔR≤±2%, R, Δ(Uab/Uac), R≤±1% Collision: 390m/s2, 4000uqw, ΔR≤±1%R Vibration: 10 to 2,000Hz, 0.75mm, 98m/s2, 6h and ΔR≤±1%R, Δ(Uab/Uac) ≤±2% Electrical endurance: 70°C, 0.5W, 1,000h ΔR≤±3%R Mechanical endurance: 100 cycles, ΔR≤±3%R steady damp-heat and ΔR≤±3%R, R1 ≥100M ohms Total mechanical travel: 3,600 ±10 degrees Starting torque: ≤20N.m Stop torque: ≥50N.m

  Characteristics: Range of nominal resistance: 10 Ohms to 2M Ohms Resistance tolerance: ±10% Terminal resistance: 1%R or 2 Ohms Contact resistance variation: 3%R or 3 Ohms Insulation resistance: R1≥1G Ohms Withstand voltage: 101.3kPa/500V, 8.5kpa/315V Effective electrical travel: 210±100 Rated maximum power working voltage: 250V +70V 0.5W +125W Temperature range: -55 to +125 degrees Celcius TCR: ±250ppm Temperature variation: R≤±2%RUab/UacR≤±1% Collision: 390m/s2, 4000uqw, R≤≥1%R Vibration: 10 to 2000Hz, 0.75mm, 98m/s2, 6h R≤±1%RUab/Uac≤±2% Climate category: R≤±3%RR1≥100M Electrical endurance: 70W, 0.5W, 1,000h, R≤±3%R Mechanical endurance: 100cycles, R≤±3%R Steady damp-heat R≤≥3%R, R1≥100M Total mechanical travel: 2500±100 Starting torque: ≤20mNm Stop torque: ≥50mN?m Standard packaging: 50 pieces per tube

  Characteristics: Range of nominal resistance: 10 Ohms to 2M Ohms Resistance tolerance: ±10% Terminal resistance: 1%R or 2 Ohms Contact resistance variation: 3%R or 3 Ohms Insulation resistance: R1≥1G Ohms Withstand voltage: 101.3kPa/500V, 8.5kpa/315V Effective electrical travel: 210±100 Rated maximum power working voltage: 250V +70V 0.5W +125W Temperature range: -55 to +125 degrees Celcius TCR: ±250ppm Temperature variation: R≤±2%RUab/UacR≤±1% Collision: 390m/s2,4000uqw, R≤≥1%R Vibration: 10 - 2000Hz, 0.75mm, 98m/s2, 6h R≤±1%RUab/Uac≤±2% Climate category: R≤±3%RR1≥100M Electrical endurance: 70W, 0.5W, 1000h, R≤±3%R Mechanical endurance: 100cycles, R≤±3%R Steady damp-heat R≤≥3%R, R1≥100M Total mechanical travel: 2500±100 Starting torque: ≤20mNm Stop torque: ≥50mN?m Standard packaging: 50 pieces per tube

  Characteristics: Range of nominal resistance: 10 Ohms to 2M Ohms Resistance tolerance: ±10% Terminal resistance: 1%R or 2 Ohms Contact resistance variation: 3%R or 3 Ohms Insulation resistance: R1≥1G Ohms Withstand voltage: 101.3kPa/500V, 8.5kpa/315V Effective electrical travel: 210±100 Rated maximum power working voltage: 250V +70V 0.5W +125W Temperature range: -55 to +125 degrees Celcius TCR: ±250ppm Temperature variation: R≤±2%RUab/UacR≤±1% Collision: 390m/s2, 4000uqw, R≤≥1%R Vibration: 10 to 2000Hz, 0.75mm, 98m/s2, 6h R≤±1%RUab/Uac≤±2% Climate category: R≤±3%RR1≥100M Electrical endurance: 70W, 0.5W, 1,000h, R≤±3%R Mechanical endurance: 100cycles, R≤±3%R Steady damp-heat R≤≥3%R, R1≥100M Total mechanical travel: 2500±100 Starting torque: ≤20mNm Stop torque: ≥50mN?m Standard packaging: 50 pieces per tube

  Mechanical characteristics: Total rotational angle: 260°±10° Rotational torque: 40 to 250 gf.cm Stopper strength: ≥1kgf.cm Electrical characteristics: Total resistance range: 100Ω to 4.7MΩ Total resistance tolerance: 500Ω1MΩ: ±20%, other: ±30% Resistance taper: linear (B) Power rating (at 70°C): ≤0.25W Maximum operating voltage: 250V AC Residual resistance: R Endurance: Rotation life: 500 to 10,000 cycles Temperature characteristic: 20 to 70°ΔRMoisture characteristic: 40°C 95% 5 hoursΔ(R/R) R≤±15% Load characteristic: 40°C 95% 5 hoursΔ(R/R) R≤±15% Soldering heat characteristic: 270°C (maximum) at 3 seconds

  Electronics characteristics: Rating: DC12V, 1A Contact resistance: 1kHz measured at small current (1A or less) Insulation resistance: a voltage of 500V DC shall be applied for a minute, and between conductors which should not make contact under normal conditions after which measurement shall be made Dielectric strength: between conductors which should not make contact under normal conditions 500V AC (50-60Hz) for 1 minute (trip current 2mA) Endurance characteristics: Solder ability: the terminals shall be dipped into soldering flux and shall be immersed into molten solder of 230±5 degrees for a period 3±0.5 seconds Resistance to soldering heat: Solder temperature: 350±10 Immersion depth: 2±0.5mm Immersion time: 3±0.5 seconds By a solder iron to have capacity of 60W Cold: the jack shall be stored at a temperature of -40±2 for 96 hours It shall be subjected to the controlled recovery conditions for 0.5 hours after which measurement shall be made Dry heat: the jack shall be stored at a temperature of -70±2 for 96 hours It shall be subjected to the controlled recovery conditions for 0.5 hours after which measurement shall be made Humidity: the pin jack shall be subject to 90%-95%RH, 40±2 for 96 hours, and shall be conditioned at room ambient conditions for a period of 30 minutes

  Electronics characteristics: Rating: DC 12V, 1A Contact resistance: 1kHz measured at small current (1A or less) Insulation resistance: a voltage of 500V DC shall be applied for a minute, and between conductors which should not make contact under normal conditions after which measurement shall be made Dielectric strength: between conductors which should not make contact under normal conditions 500V AC (50-60Hz) for 1 minute (trip current 2mA) Endurance characteristics: Solder ability: the terminals shall be dipped into soldering flux and shall be immersed into molten solder of 230±5 degrees for a period 3±0.5 seconds Resistance to soldering heat: Solder temperature: 350+/-10 Immersion depth: 2±0.5mm Immersion time: 3±0.5 seconds By a solder iron to have capacity of 60W Cold: the jack shall be stored at a temperature of -40±2 for 96 hours It shall be subjected to the controlled recovery conditions for 0.5 hours after which measurement shall be made Dry heat: the jack shall be stored at a temperature of -70±2 for 96 hours It shall be subjected to the controlled recovery conditions for 0.5 hours after which measurement shall be made Humidity: the pin jack shall be subject to 90%-95%RH, 40±2 for 96 hours, and shall be conditioned at room ambient conditions for a period of 30 minutes

   Electronics characteristics: Rating: 12DC V, 1A Contact resistance: 1kHz measured at small current (1A or less) Insulation resistance: a voltage of 500V DC shall be applied for a minute, and between conductors which should not make contact under normal conditions after which measurement shall be made Dielectric strength: between conductors which should not make contact under normal conditions 500V AC (50-60Hz) for 1 minute (trip current 2mA) Endurance characteristics: Solder ability: the terminals shall be dipped into soldering flux and shall be immersed into molten solder of 230±5 degrees for a period 3±0.5 seconds Resistance to soldering heat: Solder temperature: 350±10 Immersion depth: 2±0.5mm Immersion time: 3±0.5 seconds By a solder iron to have capacity of 60W Cold: the jack shall be stored at a temperature of -40±2 for 96 hours It shall be subjected to the controlled recovery conditions for 0.5 hours after which measurement shall be made Dry heat: the jack shall be stored at a temperature of -70±2 for 96 hours It shall be subjected to the controlled recovery conditions for 0.5 hours after which measurement shall be made Humidity: the pin jack shall be subject to 90%-95%RH, 40±2 for 96 hours, and shall be conditioned at room ambient conditions for a period of 30 minutes

  Electronics characteristics: Rating: DC 12V, 1A Contact resistance: 1kHz measured at small current (1A or less) Insulation resistance: a voltage of 500V DC shall be applied for a minute, and between conductors which should not make contact under normal conditions after which measurement shall be made Dielectric strength: between conductors which should not make contact under normal conditions 500V AC (50-60Hz) for 1 minute (trip current 2mA) Endurance characteristics: Solder ability: the terminals shall be dipped into soldering flux and shall be immersed into molten solder of 230±5 degrees for a period 3±0.5 seconds Resistance to soldering heat: Solder temperature: 350±10 Immersion depth: 2±0.5mm Immersion time: 3±0.5 seconds By a solder iron to have capacity of 60W Cold: the jack shall be stored at a temperature of -40±2 for 96 hours It shall be subjected to the controlled recovery conditions for 0.5 hours after which measurement shall be made Dry heat: the jack shall be stored at a temperature of -70±2 for 96 hours It shall be subjected to the controlled recovery conditions for 0.5 hours after which measurement shall be made Humidity: the pin jack shall be subject to 90%-95%RH, 40±2 for 96 hours, and shall be conditioned at room ambient conditions for a period of 30 minutes

  Electrical characteristics: Rated power: DC 12V, 1A Contact resistance: measurement shall be made at with small current 1000Hz(1A maximum) Insulation resistance: a voltage of 500V DC shall be applied for 1 minute after which measurement shall be made Dielectric strength: 500V AC(50Hz-60Hz) for 1 minute Trip current: 2mA Endurance characteristics: Soldering heat test: the terminal for a printed circuit board Temperature of solder: 260+/- Dip time: 5±1 seconds The terminal for a lead wire: Temperature of solder: 350±10 Dip time: 3±1 seconds Cold: the jack shall be stored for 96 hours at a temperature of -25±3 immediately after which measurement shall be made Dry heat: the jack shall be stored for 96 hours at a temperature of 70±2 immediately after which measurement shall be made Contact resistance: 50m ohms maximum Insulation resistance: 50m ohms minimum Contact pressure: 0.5N(50gf) minutes Insertion force: 3-30N(0.3-3.0kgf) Withdrawal force: 3-30N(0.3-3.0kgf)

  Electrical characteristics: Rated power: DC 12V, 1A Contact resistance: measurement shall be made at with small current 1000Hz(1A maximum) Insulation resistance: a voltage of 500V DC shall be applied for 1 minute after which measurement shall be made Dielectric strength: 500V AC(50 Hz-60Hz) for 1 minute Trip current: 2mA Endurance characteristics: Soldering heat test: the terminal for a printed circuit board Temperature of solder: 260+/- Dip time: 5±1 seconds The terminal for a lead wire: Temperature of solder: 350±10 Dip time: 3±1 seconds Cold: the jack shall be stored for 96 hours at a temperature of -25±3 immediately after which measurement shall be made Dry heat: the jack shall be stored for 96 hours at a temperature of 70±2 immediately after which measurement shall be made Contact resistance: 50m ohms maximum Insulation resistance: 50m ohms minimum Contact pressure: 0.5N(50gf) minutes Insertion force: 3-30N(0.3-3.0kgf) Withdrawal force: 3-30N(0.3-3.0kgf)

  Actuating force: 100 to 260 ±30gf Travel: 0.3 ±0.1mm Stem strength: 3Kgf Contact resistance: 50m ohms maximum Insulation resistance: 100m ohms maximum Dielectric withstanding: there shall be no breakdown Operating temperature range: -20 to 70 degrees Celsius (normal humidity, normal press) Storage temperature range: -20 to 80 degrees Celsius (normal humidity, normal press) Scope: specification covers the requirements for single key switches which have no key top (tact switches, mechanical contact)

  General specification: Scope: this specification covers the requirements for single key switches which have no key top Operating temperature range: -20-70 degree Celsius Storage temperature range: -20-80 degree Celsius Actuating force: 100-260 +/-30gf Travel: 0.3+/-0.1mm Stem strength: 3kg Contact resistance: 50m ohms maximum Insulation resistance: 100m ohms maximum Dielectric with standing: there shall be no breakdown