Pump,Motor,Generator

   Features: Conform to IEC standard, with the advantage of light weight, low noise,nice appearance, excellent electric performance Working Conditions: The altitude not exceeding 1000m above sea level. The ambient temperature subject to seasonal variations but not exceeding 40°C and not less than -15°C Motor Frame: IEC 711-100 Output(KW): 0.37kW~3kW Rated Voltage(V): 220V Frequency(HZ): 50HZ or 60HZ Raged Speed(rpm): 1400r/min 4-pole. 2800r/min 2-pole. Insulation Class: CLASS B Protection Class: IP44, IP54, IP55 Mounting Type: IMB3, IMB5, IMB14, IMB35 Duty: S1 Methods of Cooling: IC0141

   JY Series Single-phase capacitor start motor. These motors are suitable for the situation that require the higher starting torque and the limited starting current. The motors can be used on driving all kinds of small machine that need full load starting. The motors of this series are totally enclosed and fan cooled, possess No.09, No.1 and No.2 three frame size and with the starting capacitor on the top of the motor. Operating Conditions: Ambient temperature: -15 oC to 40 oC Altitude: not exceed 1000m Rated voltage: 110V, 115V, 120V, 220V, 230V, 240V Rated frequency: 50Hz, 60Hz Protection class: IP44, IP54, IP55 Insulation class: B, F Cooling method: ICO141 Duty: St(continuous)

   YC series heavy-duty single-phase motors are suitable for small size machine tools and water pumps.especially for family workshops where only single-phase power supply is available.capacitor starting. YCL series heavy-duty capacitor start and run. comparing with the same output YC series motor,YCL series temperature raising reduce 8.74k on average,efficiency improve 4.21 percent,power factor raise 0.16 Protection class:IP44 IP54 IP55 Insulation class:B,F Rated frequency:50HZ 60HZ Rated output:0.18kw-7.5kw Shell material:cast iron

  Y2 series three-phase induction motor is specially designed for European market, whose terminal box is located on the top. This motor has a very compact structure and attractive appearance. The sizes and mounting dimensions are produced according to the IEC standard. The motor has some good features, such as high efficiency, energy-saving, high starting torque and easy maintenance. We can also supply aluminum housing type for frame size below IEC132. Y2 series motors can be widely used as driving equipments of various machineries, such as, machine tools, blowers, pumps, compressors, transporters, agricultural and food processing. Specifications & FeaturesRated voltage: 380V or on request, Rated frequency: 50Hz or 60HzConnection: Star-connection for 3KW or less while delta-connection for 4KW or more. Duty/Rating: Continuous (S1). Insulation class: F, the temperature rise of the stator winding is examined at 80K (by resistance method). Protection class: The main body of the motor is IP54, terminal box reaches IP55Cooling method: ICO141 (cooled by SELF-FAN) Improving electromagnetic and construction design, low noise and little vibration.Operating Conditions Ambient temperature: -15≤θ≤40Altitude: not exceeding 1000meters above sea level. Relative humidity less than 90% .Available typeFrame H63 to 315, 2/4/6/8 poles, Rated output: 0.12KW-200KWB3/B5/B14/B35/B34 mounting; Mounting dimensions according to IEC60034 standard

   Y series motors are totally enclosed fan cooled, three-phase squirrel cage inductionmotors, it is newly designed in conformity with the relevant requirements of IECstandards. Y series motors have outstanding performance, such as high efficiency, energy-saving,high starting starting torque, low noise, little vibration, reliable operation andeasy maintenance, etc.Y series motors are widely used in places, where there doesn't exist combustible,explosive or corrosive gas, tools, pumps, fans, transport machinery, mixer, agriculturemachinery and food machines, etc. OPERATING CONDITIONS: Ambient temperature: -15oCAltitude: not exceed 1000mRated voltage: 220/380V,? 380/660V Rated frequency: 50Hz Protection class: IP44, IP54 Insulation class: B. F Cooling method: ICO141 Duty: S1(continuous) Connection: Star-connection For up to 3kW, delta-connection for 4kW and above.

  Features:1) TZH series three-phase compound excitation AC synchronous generator2) Manufactured in conformity with JB / T8981-1999 and IEC34-1 standards3) Protection class: IP21, Insulation: Class B or F 4) The rotor structure is concealed type 5) More reliable performance 6) Compared with STC series generators, TZH series generators have five??? advantages of compound excitation, simple circuit, high reliability, easy??? maintenance and excellent dynamic characteristics 7) When loaded or unloaded suddenly, the light of the circuit will not twinkle8) Strong starting system: even the motors only with its 70% capacity volume can??? be directly started and the switch will not trip9) Approaching sine voltage wave and regulated power supply, output voltage can be??? safely used on computers10) The deviation of the 3-phase line voltage will be less than 3% when the??? generators undertake unbalanced loading11) Altitude: not exceeds 1,000m12) Cooling air temperature: 258 ~ 313F (-15oC ~ 40oC)13) Relative air humidity: not exceeds 90%14) Frame No.: 225S ~ 355L????? 15) Output: 37.5 ~ 312.5kVA, 30 ~ 250kW

  Designed to serve as power generating unit of small capacity, supply electricity for lighting purpose Engine can be connected with steel or flexible materials Used in ships and household electric devices used in towns or villages Drip-resistant, salient pole rotating field, self excitation and constant voltage type Used with high quality electric magnetic and electrical materials Stator insulation is class B Elegant appearance Tight construction IEC standard are adopted on dimensions Dimensions are suitable for using in Australia, Europe, America and other countries with end covers to be model B Easy to maintain Protection: IP21 Insulation: class B Rated speed: 1,500/1,800rpm Rated voltage: 400/230V Rated output power: 3 to 50kW Rated frequency: 50/60Hz

   The ST series generators are mainly designed to serve as small capacity power generating units for electrical supply for lighting purposes on ships as well as for standard household devices used in towns or villages.The generators are of drip-proof construction with salient pole rotating field self-excitation and constant voltage. The inside construction is of high international quality electrical components. The Stator insulation is of Class E (or B as required) and rotor insulation is Class B. These generators are compact, attractively finished and are very easy to maintain. Dimensions are adapted to IEC standards which make them highly suitable for Australia, Europe, America and other countries where end covers of model B are required. The alternators are a harmonic wave, self-excitation constant voltage system with automatic voltage control excitation. They have excellent dynamic performance characteristics; they are convenient and are very reliable in operation. The voltage of the alternator is 230V or 115V (or 240V /120V if required) and the frequency is 50Hz or 60Hz again as required. Its operation can be in continuous duty mode. The alternator can be coupled with a prime mover directly or through a V-belt drive. With 5% speed change of the prime mover on load, the variation of 0-100% at voltage of 230V or 115V 50Hz or 60Hz, you could still get a satisfactory constant-Voltage performance.

   YGP features Powered by air-cooled 4-stroke OHV gasoline engine Pressure Casting aluminim pump body High quality and mechanical sealed equipment Self sucking and high-pressure. Compact in structure and light weight. YGF features The efficient light weight aluminum die-cast pump in 2",3",4"inlet &outlet delivers big volume water. Powered by air-cooled 4-stroke OHV gasoline engine. The highly effective mechanical seal with a special carbon ceramic provides extra durability. The entire unit is protected by a sturdy steel rolloven pipe frame.

   Deep Well Pump Working Principle:The JDW pump comprises ejector unit and a centrifugal pump.The ejector unit in the fact is a Venturi system cinsisting of a tube and a nozzle,lowered in a 4" well and connected to the pump body by two pipes.The total delivery produced by the centrifugal impeller is sent only partiy to the delivery outline.The remaining water is circulated an jet through the nozzle in Venturi system.With tremendous speed,this flow lead the water in the well and deliver toward to the ground.By the suction of the centrifugal pump,the water come in to the pump and gain a energy through the impeller,and once again,partly of the water returnto the Venturi system through smaller pipe and circling.The ejector unit can ben installed on the pump body works like JET pump.These pumps are suitable for pumping clean water and chemically nonaggressive fluids.They are extremely reliable,economical and simple to use,finding many uses in domesticapplications and the automatic distribution of water from small and medium-sized surge tanks from a automatic booster systems to supply water.To ensure adequate counter-pressure,it is always to intall a foot valve with a filter on the suction opening.These pumps should be installed in a covered area,prtected against the weather. MATERIAL AND WORKING LIMITSPump body: Cast ironImpeller: Brass/ABS/NorylDiffuser: Noryl/PPO/ABS/Cast ironMotor Housing: Cast ironFront cover: Aluminum/Cast ironMechanical seal: Stainless steel(graphite to cetamic)Shaft: 45#steel or stainless ironBearing:SKF/NTN/NSK/ChinaInsulation class:B and FProtection class:IP44 and IP54Max.Pressure:10 bar

   The swimming pool water pump is specially developed according to the operational features of the swimming pools both domestic and abroad and is suitable for cleaning and removing dirt to keep the water in good quality and for eliminating the inconvenience to change the water often. The pump is equipped with a special filtering system, which is fully mounted on a hand truck, where the process from sucking water to becoming standard water quality by filtering is finished. The working principle of the swimming pool water pumps and the completing device is as below:1. Both water and filth are sucked into the suction disk2. Then go into the pump to be roughly filtered to get rid of larger grained dirt such as leaves3. Then go into the filter tank through the transport flexible tube to be fine filtered4. The clean water via filtering goes back to the pool, thus the filtering is finished This set of equipment has an advantage that it is unnecessary to change the pool water, only periodically using it to clean and filter and the operation becomes facilitated with the hand truck used. It is powerfully competitive in the world market due to its convenient movement and superior performance. It can also be used for the cold - hot circulation system of sauna. Technical parameters:1) Pump body: ABS 2) Impeller: Noryl? ABS 3) Motor closed, externally ventilated 4) Insulation class B (class F if required) 5) Protection class IP44 or IP54 6) Duty continuously rated 7) Mechanical seal Φ12 and Φ ceramic steatite / metalized carbon 8) Shaft stainless steel 9) Thermal protector

   JET-P series are suitable for pumping clean water. They are particularly suitable for domestic applications such as supply water from well, pool etc, the automatic distribution of water by surge tanks and pressure switch, gardening, and increasing of water pressure. WORKING CONDITIONSMax Temperature of Fluid up to +40°CMax Pressure 8bar, Max Ambient Temperature up to 40°C

   Operating conditions:* Max. working pressure: 4.5 bars* Liquid temperature up to 60°C* Ambient temperature up to 40°C* Total suction lift up to 9M* Continuous duty Motor:* Two-pole induction motor (2,850rpm)* Insulation class: B* Protection: IP44 Materials:* Pump body: cast iron* Motor support: cast iron* Motor housing: aluminum* Impeller: brass* Diffuser: Noryl* Shaft with rotor: superior steel* Mechanical seal: carbon / ceramic * Single phase 220 - 240V, 50Hz* Single phase 110 - 127V, 60Hz as per requests* Single / three-phase 220V, 60Hz as per requests

   Operating conditions:* Max. working pressure: 4.5 bars* Liquid temperature up to 60°C* Ambient temperature up to 40°C* Total suction lift up to 9M* Continuous duty Motor:* Two-pole induction motor (2,850rpm)* Insulation class: B* Protection: IP44 Materials:* Pump body: cast iron* Motor support: cast iron* Motor housing: aluminum* Impeller: brass* Diffuser: Noryl* Shaft with rotor: superior steel* Mechanical seal: carbon / ceramic * Single phase 220 - 240V, 50Hz* Single phase 110 - 127V, 60Hz as per requests* Single / three-phase 220V, 60Hz as per requests

   These three series self-priming JET pumps equipped with same Venturi system each. They are suitable to convey clean water and non-aggressive chemical fluids, even with liquid mixed with gas, from well in continuous duty; they are also indicated to increase water pressure in centralized water systems, for small irrigation systems, for watering gardens, for washing systems with water jets, for fountains, etc. It is normally advisable to install a foot valve on the suction branch. WORKING CONDITIONSMax Temperature of Fluid up to +40°CMax Pressure 8bar, Max Ambient Temperature up to 40°C

  Operating conditions*Liquid temperature up to 60*Ambient temperature up to 40*Total suction lift up to 9m.*Continuous duty?Motor*Two-pole induction motor(n=2850r.p.m)*Insulation Class B*Protection IP44?Material*Pump body: Cast iron*Motor support: Cast iron*Motor housing: Aluminum*Impeller: Brass*Diffuser:Noryl*Single with rotor:45#Steel,AISI 416 stainless steel if request*Mechanical seal:Carbon/Ceramic?Single phase 220V-240V/50HSingle phase 110V-127V/60Hz If request

   NFM pumps are specifically designed to achieve high delivery rates with low to medium heads for industrial and agricultural use. Two flanges with screw make it installation and maintenance simple and easy. Its volute and impeller make it able to pump water that is even fairly dirty. High delivery rates under continuous or heavy duty, making them advantageous for rain and gravity irrigation, for pumping water from lakes, river, wells and for a wide variety of industrial uses where high delivery rates must be achieved at low to average heads. Operating Limits Max temperature of fluid up to +80oC Max pressure 10bar Max ambient temperature up to 40oC

   DTM series are single stage centrifugal pumps, suitable for agriculture and industrial applications to convey clean liquids and non-aggressive chemical fluids. It's hydraulic characteristic is lower head but bigger capacity. Working conditions:1) Max. temperature of fluid up to: 80°C2) Max. ambient temperature up to: 40°C3) Max. pressure: 10 Bar Structural characteristics:1) Pump casing: cast iron2) Impeller: brass, cast iron, aluminum3) Motor housing: closed, externally ventilated4) Mechanical seal: stainless steel (carbon to ceramic)5) Shaft: 45# steel or stainless steel6) Bearing: SKF/NTN/NSK/China7) Insulation class: B and F8) Protection class: IP44 and IP549) Thermal protector available if required

   DKm pumps are specifically designed for industrial and agricultural use. High delivery rates under continuous or heavy duty, making them advantageous for rain and gravity irrigation, for pumping water from lakes, river, wells and for a wide variety of industrial uses where high delivery rates must e achieved at low to average heads. With a single centrifugal impeller cantilevered on the motor shaft directly, the DKm pumps have a compact size, extremely reliable, very simple to use and almost maintenance-free. WORKING CONDITIONSMax Temperature of Fluid up to +40°CMax Pressure 8bar, Max Ambient Temperature up to 40°C

   Operating conditions:* Max. working pressure: 2.0 bars * Liquid temperature up to 60°C* Ambient temperature up to 40°C* Total suction lift up to 9M* Continuous duty Motor:* Two-pole induction motor (2,850rpm)* Insulation class: B* Protection: IP44 Materials:* Pump body: cast iron* Motor support: cast iron* Motor housing: aluminum* Impeller: brass* Shaft with rotor: superior steel* Mechanical seal: carbon / ceramic * Single phase 220 - 240V, 50Hz* Single phase 110 - 127V, 60Hz as per requests* Single / three-phase 220V, 60Hz as per requests

   Operating conditions:* Max. working pressure: 4.6 bars * Liquid temperature up to 60°C* Ambient temperature up to 40°C* Total suction lift up to 9M* Continuous duty Motor:* Two-pole induction motor (2,850rpm)* Insulation class: B* Protection: IP44 Materials:* Pump body: cast iron* Motor support: cast iron* Motor housing: aluminum* Impeller: brass* Shaft with rotor: superior steel* Mechanical seal: carbon / ceramic * Single phase 220 - 240V, 50Hz* Single phase 110 - 127V, 60Hz as per requests* Single / three-phase 220V, 60Hz as per requests

   DBZ series pumps are suitable for handing clean water not containing abrasive particles and fluids which are not chemically aggressive to the pump components. They are particular suitable for domestic and industrial applications, such as water supply for recirculation in air conditioners and refrigerators, industrial water uses in general, and the automatic distribution of water from surge tanks, watering gardens, lifting water from tanks or wells down to 9m depth.Working conditions: 1) Max. temperature of fluid up to: 80°C 2) Max. ambient temperature up to: 40°C 3) Max. pressure: 8 BarStructural characteristics:1) Pump casing: cast iron2) Impeller: brass 3) Diffuser: cast iron 4) Motor housing: steel 5) Mechanical seal: stainless steel (granite to ceramic) 6) Shaft: 45# steel or stainless steel 7) Bearing: SKF/NTN/NSK/China 8) Insulation class: B and F 9) Protection class: IP44 and IP54

  CPW series centrifugal pumps are single stage,high efficient electric pumps,consisted fo a mininature motor and a single impeller centrifugal pump.they have a good performance in Big Capacity and High Head.They are widely used in well-pumping,water supplying,edcanting,mixing and irrigating for civil,industry and agriculture,etc.

   GP series pumps are suitable for handing clean water not containing abrasive particlesand fluids which are not chemically aggressive to the pump components. Theyare particular suitable for domestic and industrial applications, such as watersupply for recirculation in air conditioners and refrigerators, industrial wateruses in general, and the automatic distribution of water from surge tanks, wateringgardens, lifting water from tanks or wells down to 9m depth. Working conditions:1) Max. temperature of fluid up to: 80°C2) Max. ambient temperature up to: 40°C3) Max. pressure: 8 Bar Structural characteristics:1) Pump casing: cast iron2) Impeller: brass 3) Diffuser: brass 4) Motor housing: cast iron5) Pump-motor adaptor: aluminum 6) Mechanical seal: stainless steel (granite to ceramic)7) Shaft: 45# steel or stainless steel8) Bearing: SKF/NTN/NSK/China9) Insulation class: B and F10) Protection class: IP44 and IP54

  Features Specifications: BA3 LQ CP PN Series Electric Clean Water PumpTheory: Electromagnetic Pump? Usage: Water? Pump Body:: Cast Iron? Shaft:: Carbon Steel/Stainless Steel? Protection:: IP 44/IP 54? Insulation:: Class B/Class F? Impeller:: Brass?

  Operating conditions*Liquid temperature up to 60*Ambient temperature up to 40*Total suction lift up to 9mt.*Continuous duty?Motor*Two-pole induction motor(n=2850r.p.m)*Insulation Class B*Protection IP44?Material*Pump body: Cast iron*Motor support: Cast iron*Motor housing: Aluminum*Impeller: Brass*Shaft with rotor: 45# Steel,AISI 416 stainless steel if request*Mechanical seal: Carbon/CeramicSingle phase 220V-240V/50HzSingle phase 110V-127V/60Hz if requestSingle/three phase 220V/60Hz if request

  Operating conditions*Liquid temperature up to 60*Ambient temperature up to 40*Total suction lift up to 9m*Continuous duty?Motor*Two-pole induction motor(n=2850r.p.m)*Insulation Class B*Protection IP44?Material*Pump body: Cast iron*Motor support: Cast iron*Motor housing: Aluminum*Impeller: Brass*Shaft with rotor: 45# Steel,AISI 416 stainless steel if request*Mechanical seal: Carbon/CeramicSingle phase 220V-240V/50HzSingle phase 110V-127V/60Hz if requestSingle/three phase 220V/60Hz if request

   Operating conditions:* Liquid temperature up to 60°C* Ambient temperature up to 40°C* Total suction lift up to 9MT* Continuous duty Motor:* Two-pole induction motor (2,850rpm)* Insulation class: B* Protection: IP44 Materials:* Pump body: cast iron* Motor support: cast iron* Motor housing: aluminum* Impeller: brass* Shaft with rotor: superior steel* Mechanical seal: carbon / ceramic * Single phase 220 - 240V, 50Hz* Single phase 110 - 127V, 60Hz as per requests* Single / three-phase 220V, 60Hz as per requests