Crusher Machinery Series,Grinding Mill Series and more.

  HGM series of Three-Ring & Medium-Speed MicroPowder Grinder is a new kind of micro-powder processing equipment, which is invented through more than twenty times experiments and improvements, and based on twenty years of mill manufacture experience while absorbing advanced international machine manufacture techniques. HGM series of Three-Ring & Medium-Speed MicroPowder Grinder is mainly used in processing non-inflammable, non-explosive, brittle material with hardness below six mohs, such as calcite, chalk, limestone, dolomite, kaolin, bentonite, talc, mica, magnesite, pyrophillite, ceyssatite, barite, gypsum, alunite, granite, fluorite, phosphate rock, kalium ore, float stone, more than 200 kinds of materials. Working Principle:The motor drives the main shaft and every turnplate through the reducer. The reducer drives dozens of rollers to rotate against race way of ring through pin. Small materials crushed by hammer crusher is transported into hopper by elevator, and then vibrating feeder shall feed material to the central part of upper turnplate evenly. The material falls to circle under the centrifugal force and comes down to raceway of ring to be crushed into powder. After grinded in the first race way, the material goes to the second and third turnplate. The blower inhales the external air into the mill and carries the powder after third turnplate into powder-separator. Turbine in the separator makes the coarse powder drop down and regrinded and the fine powder shall go into cyclone powder collector together with air current and go down through discharge valve as final product; at the same time, air current with a little dusts goes out through blower and muffler after purified by filter.Capabilities and Characteristics:Three-Ring & Medium-Speed MicroPowder Mill has high efficiency and low cost. Its capacity is raised by 40% compared with airflow mill and mix mill on the condition that the materials, the drive and the fineness of the final powder are the same. The life span of tear & wear parts is more than that of straight impact crusher and turbine mill under the circumstance of same materials and fineness of the final powder. Usually, its life span is more than one year. There is no rolling bearing and screw in the grinding cavity, so as to avoid the damage to the machine caused by tear & wear of bearing and seals and the looseness of screws. The fineness of powder can reach ≦5μm with d97 once.

  TGM Series Super Pressure Trapezium Mill is the latest grinding mill. TGM Series Supper Pressure Trapezium Mill is reseached and designed by our experts basing on long term experiences of mill research and development, and following to numbers of customers' using requirements and suggestions home and aboard. The TGM Series Super Pressure Trapezium Mill adopts our patented technologies, like trapezium working surface, flexible connection, roller linked pressure boost, etc. TGM Series Super Pressure Trapezium Mill has reached the advanced international level of powder making equipment manufacturing.TGM Series Super Pressure Trapezium Mill mainly consists of mainframe, speed reducer, powder seperator, blower, bag filter, pipes, powder collector, motor, etc. The peripheral equipments are jaw crusher, bucket elevator, feeder, hopper, electric control panel, etc. TGM Series Super Pressure Trapezium Mill can grind all kinds of non-flammable and non-explosive minerals with Moh’s hardness lower than 9 and humidity less than 6%，and TGM Series Super Pressure Trapezium Mill is widely used in metallurgy, manufacture of building materials, chemical industry, minig industry, etc.Working Principle:Large materials are crushed by Jaw crusher to the needed sizes firstly, then the materials are elevated to storage hopper by bucket elevator, third, the materials are fed into the grinding chamber for grinding by vibrating feeder equably and continuously. The powder after grinding goes upwards together with the airflow, after seperating by powder seperator, those which can meet the fineness requirement enters into the cyclone powder collector through pipe together with the airflow, and then discharged from the discharge valve as final products. The airflow is sucked into centrifugal blower through wind recycling pipe at the upper part of cyclone powder collector. The mainframe is drived by the speed reducer through the central axis in the mill.The quincunx stand connected with the upper part of central axis, at the quincunx stand, rollers are set and by which the vibrating pivot formed. Below the quincunx stand and rollers there is shoval system. Materials are fed into the space between rollers and shovels when they are turning, and then be grinded by the pressure produced when rollers are turning, thus powder is made.Characteristics:The diameters of each part of rollers and rings are different, the upper part is big and the lower part is small, then they formed a trapezium form. This form can reduce materials’ sliding speed downwards and prolong the grinding time for materials, thus the grinding efficiency is increased.; the pressing springs have the functions of balancing and pressure increasing; the flexible connection can make the mill stable, decrease the shocking and avoid sympathetic vibration; high density powder seperator impeller decreases the air resistance and increases powder collecting fineness and capacity; the efficiency of energy saving and high efficient centrifugal blower is as high as 83%. Model:TGM160Max input size(mm):Final size(mm):1.6-0.045mini fineness is 0.038Output(t/h):9-22Weight(t):35

  TGM Series Super Pressure Trapezium Mill is the latest grinding mill. TGM Series Supper Pressure Trapezium Mill is reseached and designed by our experts basing on long term experiences of mill research and development, and following to numbers of customers' using requirements and suggestions home and aboard. The TGM Series Super Pressure Trapezium Mill adopts our patented technologies, like trapezium working surface, flexible connection, roller linked pressure boost, etc. TGM Series Super Pressure Trapezium Mill has reached the advanced international level of powder making equipment manufacturing.TGM Series Super Pressure Trapezium Mill mainly consists of mainframe, speed reducer, powder seperator, blower, bag filter, pipes, powder collector, motor, etc. The peripheral equipments are jaw crusher, bucket elevator, feeder, hopper, electric control panel, etc. TGM Series Super Pressure Trapezium Mill can grind all kinds of non-flammable and non-explosive minerals with Moh’s hardness lower than 9 and humidity less than 6%，and TGM Series Super Pressure Trapezium Mill is widely used in metallurgy, manufacture of building materials, chemical industry, minig industry, etc.Working Principle:Large materials are crushed by Jaw crusher to the needed sizes firstly, then the materials are elevated to storage hopper by bucket elevator, third, the materials are fed into the grinding chamber for grinding by vibrating feeder equably and continuously. The powder after grinding goes upwards together with the airflow, after seperating by powder seperator, those which can meet the fineness requirement enters into the cyclone powder collector through pipe together with the airflow, and then discharged from the discharge valve as final products. The airflow is sucked into centrifugal blower through wind recycling pipe at the upper part of cyclone powder collector. The mainframe is drived by the speed reducer through the central axis in the mill.The quincunx stand connected with the upper part of central axis, at the quincunx stand, rollers are set and by which the vibrating pivot formed. Below the quincunx stand and rollers there is shoval system. Materials are fed into the space between rollers and shovels when they are turning, and then be grinded by the pressure produced when rollers are turning, thus powder is made.Characteristics:The diameters of each part of rollers and rings are different, the upper part is big and the lower part is small, then they formed a trapezium form. This form can reduce materials’ sliding speed downwards and prolong the grinding time for materials, thus the grinding efficiency is increased.; the pressing springs have the functions of balancing and pressure increasing; the flexible connection can make the mill stable, decrease the shocking and avoid sympathetic vibration; high density powder seperator impeller decreases the air resistance and increases powder collecting fineness and capacity; the efficiency of energy saving and high efficient centrifugal blower is as high as 83%. Model:TGM160Max input size(mm):Final size(mm):1.6-0.045mini fineness is 0.038Output(t/h):9-22Weight(t):35

  HGM series of Three-Ring & Medium-Speed MicroPowder Grinder is a new kind of micro-powder processing equipment, which is invented through more than twenty times experiments and improvements, and based on twenty years of mill manufacture experience while absorbing advanced international machine manufacture techniques. HGM series of Three-Ring & Medium-Speed MicroPowder Grinder is mainly used in processing non-inflammable, non-explosive, brittle material with hardness below six mohs, such as calcite, chalk, limestone, dolomite, kaolin, bentonite, talc, mica, magnesite, pyrophillite, ceyssatite, barite, gypsum, alunite, granite, fluorite, phosphate rock, kalium ore, float stone, more than 200 kinds of materials. Working Principle:The motor drives the main shaft and every turnplate through the reducer. The reducer drives dozens of rollers to rotate against race way of ring through pin. Small materials crushed by hammer crusher is transported into hopper by elevator, and then vibrating feeder shall feed material to the central part of upper turnplate evenly. The material falls to circle under the centrifugal force and comes down to raceway of ring to be crushed into powder. After grinded in the first race way, the material goes to the second and third turnplate. The blower inhales the external air into the mill and carries the powder after third turnplate into powder-separator. Turbine in the separator makes the coarse powder drop down and regrinded and the fine powder shall go into cyclone powder collector together with air current and go down through discharge valve as final product; at the same time, air current with a little dusts goes out through blower and muffler after purified by filter.Capabilities and Characteristics:Three-Ring & Medium-Speed MicroPowder Mill has high efficiency and low cost. Its capacity is raised by 40% compared with airflow mill and mix mill on the condition that the materials, the drive and the fineness of the final powder are the same. The life span of tear & wear parts is more than that of straight impact crusher and turbine mill under the circumstance of same materials and fineness of the final powder. Usually, its life span is more than one year. There is no rolling bearing and screw in the grinding cavity, so as to avoid the damage to the machine caused by tear & wear of bearing and seals and the looseness of screws. The fineness of powder can reach ≦5μm with d97 once.

  YZS Vibrating screen is used to separate the stuff and composed of main frame, screen web, electric motor, eccentric bock, rubber spring, coupler and so on .We will offer suitable type according to your requirements.YZS vibrating screen is widely used for classification in mining,construction material,transportation,energy,ect. YZS Vibrating screen Features: Simple and reliable. 1.No transmission of screen panels. 2.Easy change of screen plates. 3.High screening capacity. 4.Rigid and vibrating resistance screen body. 5.High durability. Models: 2YZS1548, 3YZS1548, 2YZS1848, 3YZS1848, 2YZS1860, 3YZS1860, 2YZS2160, 3YZS2160, 2YZS2460Screen size(mm):4800×1500~6000×2400NO. of layer:2 or 3Screen mesh(mm):3~150Max. feed size(mm):400Handling capacity(t/h):30~810Motor power(kw):15~37Vibrating frequency(r/min):730~870Double swing(mm):5~9 Notice: Any change of? technical data shall not be advised additionally

  The Vibrating feeder is a kind of linear direction feeding equipment.The features of vibrating feeder:1.smooth vibrating2.reliable in operation3.long service lifetime 4.suitable for feeding.The Vibrating feeder is widely used in mining,building-material,chemical industry in the crushing and screening plants.Model:GZD-1300x4900Size of Funnel:1300x4900Capacity(t/h):450-600Powder(Kw):22

  The national IPR product─Straight Centrifugal Grinder Mill is our latest type which is designed by our experts who have long experience and hard research in mill equipment, which has opened a new time of industrial flour mill with high efficiency and low energy consumption. Straight Centrifugal Grinder Mill is used to grind various non-inflammable and non-explosive stuff in mining, building, chemical, metallurgical industry, etc. Straight Centrifugal Grinder can grind high, medial and low hardness material whose Moth's hardness is below 9.5,such as silica carbide, zirconium, quartz stone, granite, barite, marble, limestone, soap stone, calcium sulphate stone, slag, ceramic prismatic, glass, etc. The working principle of straight centrifugal grinder mill:The motor drives the rollers suspension frame through flywheel and shaft, and the rollers will rotate around the ring with the rollers suspension frame. Deduster will eliminate the dust, at the same tiem, it will also carry away the heat and there is no dust pollution. Dry production:The stuff enters the input opening, after distributed by distribute cone, it falls down the ring like the waterfall. It will be grinded to powder by the rollers in turn, discharged from the discharge pipe. Wet productionThe process assembles the Dry Production; the difference lies in adding water and the dehydration after grinding. This process can be designed according the user's requirements.

  This series XSD Sand Washing Machines are a kind of water washing style equipment to be matched with the sand making machine and can reduce the dust and stone powder which mixes with the final sand, so sand making machine can improve the quality of the sand. XSD series Sand making machine is used in building plant, quarry, concrete plant, dam building, casting-70 sand, glass factory’s quartz sand and refilling pressure sand. Working Principle of Sand Washing Machine:The electric motor runs slowly with the impellor after decelerated by the belt, decelerator and gears wheel. The sand and stone flow into washing launder from feeding launder, rolls with the impellor, and grinds each other. The impurity covering the sand is washing away. At the same time, add more water, the strong water flow will take away waste and some low-weight wastes from washing launder. Through the above process, the washing function is finished. The clean sand and stone is lift up by vane. When it goes up slowly, the water begins to drop through the mesh and fall back in the washing launder. On one hand, water is removed from the sand and stone; on the other hand, the water can be fully used. Finally, the sand and stone goes to the out launder from the rotary impellor to finish the washing task.Characteristics of Sand Washing Machine:Reasonable structure, large capacity, low consumption, little loss of the sand during the washing process, low failure rate. Models: XSD2610, XSD2816, XSD3016Model: XSD2610Wheel Size (mm): Φ2600×1000Max feed size (mm): 10Power (Kw): 5.5Weight (t): 2.7Capacity (t/h): 50Overall dimension (mm): 3255×1982×2690 Model: XSD2816Wheel Size (mm): Φ2800×1000Max feed size (mm): 10Power (Kw): 11Weight (t): 3Capacity (t/h): 100Overall dimension (mm): 3540×3000×2880 Model: XSD3016Wheel Size (mm): Φ3000×1600Max feed size (mm): 10Power (Kw): 15Weight (t): 3.3Capacity (t/h): 150Overall dimension (mm): 3845×3000×3080 Notice: Any change of? technical data shall not be advised additionally Also,our company produces other mining machines and construction machines.Such as:crushers, grinders, mills, sand makinging machines, ect. welcome to enquiry!

  Impact Crusher is mainly used to crush many kinds of large, medium, small materials such as rock or stone whose side length is less than 500mm, and compression resistance should not be more than 350Mpa. The impact crusher is widely used in hydroelectricity, highway, artificial rock, stone and sand, building material, etc.Working Principle of Impact Crusher:When the impact crusher works, the motor drives the rotor rotate with high speed, on the rotor where installed the hammers. When the materials get into the area which the hammers effect, under the impact function of the hammer at a high speed, the materials are thrown to the impact device above the rotor continuously. And then the materials are rebounded from the impact liner to the area where the hammers effects for being recrushed. The materials from large to small all to be crushed at the impact chamber repeatedly. The process won’t stop till the material are crushed to the required size and then discharged from outlet. The main features of impact crusher: 1.Connected with locking sleeve assembly. 2.Final product with cubical shape. 3.The blow bar with high chrome. 4.Easy maintenance. Hydraulic or hand opening. 5.Reliable operation. Impact plate with a special shape. Model: PF1315Feed Opening(mm):860x1520Max Feed Size(mm):Capacity(t/h):120-250Powder(kw):180-260Weight:19(t) Any change of technical data shall not be advised additionally.

  High Pressure Suspension Mill is a new kind of mill, which is invented with great concentration and on the basis of many years of powder processing experiences. This invention starts an epoch of high efficiency and low cost in international mining industry. High Pressure Suspension Mill can be used to grind non-inflammable and non-explosive materials with Moh’s hardness below 9.3 and moisture content below 6%, such as barite, limestone, pottery, scoria. Size of final products can be adjusted between 80-425 mesh (The fineness can reach 1000 mesh).High Pressure Suspension Mill can produce coarse powder between 30-80 mesh by adding special equipment. This machine is widely used in the fields like mining, chemical industry, construction materials, metallurgy, etc. Working Principle:In the mainframe of High Pressure Suspension Mill, there are strong springs with pressure as high as1000-1500 kg equipped on the roller suspender. When High Pressure Suspension Mill works, the roller rotates around the principal axis, and clings to ring under the effect of the strong spring and eccentricity. Its press is 1.2 times of Raymond mill under the same press condition, so the production is largely increased. When the materials are sent into the grinding chamber, they are brought to the space between the roller and ring and get grinded. Then the powder grinded will be blown into separator. The fine powder after departed with the air is discharged through the outlet as final product. The large-sized powder falls back for regrinding. The air will be back to the blower for repetition of the above process. The left air wil come to thel bag filter to get cleaned. When the wear and tear between roller and the ring reaches certain degree, adjust the length of the strong spring,, so to keep the invariable pressure between the roller and the ring, to make sure the stable production and the fineness.Characteristics:1. Compared with other mills, its capacity increases by 10%-20% under the same power condition, and compression force of rollers to material improve 800-1200kgf under the force of high-pressure spring.2. Size of final product can be 0.613mm (30mesh) –0.033mm (425mesh). Some can reach the fineness of 0.013mm (1000 mesh).3. High Pressure Suspension Mill meets the requirement of national dust-dump standard.4. The separator can be adjusted very easily.5. The multi-class seals are adopted to keep the grinding equipment tightly closed. ?

  The hammer crusher (hammer mill) crushes by the collisions between high-speed hammer and materiasl, and the hammer crusher (hammer mill) features in its simple structure, high reduction ration, high efficiency, etc. The PC hammer crusher (hammer mill) was developed for both dry and wet crushing of brittle, medium-hard materials for the mining, cement, coal, metallurgic, construction material, road building, and petroleum & chemical industries. Operating principle of Hammer Crusher:In the hammer mill machine, the motor drives the rotor rotate at a high speed through the belt, and on the rotor there are series hammers. When the materials get into the working area of hammers, the rotating hammers with high rotation speed are crushing them, the products which are crushed to meet the required size can be discharged by the outlet and become the final products, the large size products are brought back to the crushing area by the hammers for being recrushed until they reached the required size. Models: PC400×300~PC800×1000;PCH0606;PCH0808;PCH1010 Model : PC400×300Max feed size (mm) : 30Handing capacity (t/h): 5 - 8Power of motor (Kw) : 11Weight (t) : 1.5 Model : PC600×400Max feed size (mm) : 100Handing capacity (t/h): 10 - 15Power of motor (Kw) : 18.5Weight (t) : 3 Model : PC800×600Max feed size (mm) : 150Handing capacity (t/h): 20 - 25Power of motor (Kw) : 55Weight (t) : 7 Model : PC800×1000Max feed size (mm) : 280Handing capacity (t/h): 20 - 50Power of motor (Kw) : 110Weight (t) : 12 Circuit Type hammer mill:Model : PCH0606Max feed size (mm) : 200Handing capacity (t/h): 18 - 30Power of motor (Kw) : 30Weight (t) : 17 Model : PCH0808Max feed size (mm) : 250Handing capacity (t/h): 30 - 50Power of motor (Kw) : 45Weight (t) : 29 Model : PCH1010Max feed size (mm) : 300Handing capacity (t/h): 45 - 80Power of motor (Kw) : 90Weight (t) : 52 Notice: Any change of? technical data shall not be advised additionally. Also,our company produces other mining machines and construction machines.Such as:jaw crusher, impact crusher,hammer crusher, cone crusher and grinders, mills, sand machines,ect. welcome to enquiry!

  Cone crusher is suitable to crush various kinds of ores and rocks of medium or above medium hardness. Compare with jaw crusher, cone crusher is of stable structure, high efficiency, easy adjustment, and use economically, etc. The spring safety system of crusher acts as an overloading protection system that allows metals to pass through the crushing chamber so as not to damage the cone crusher. The safety system uses dry oil and water as two kinds of sealed formation to make plaster powder and engine oil separated to make surereliable performance. The type of crushing chamber depends upon the size of feeding and fineness of the crushed product. The standard type(PYB) is applied to medium crushing, the medium type is applied to medium or fine crushing and the short head type is applied to fine crushing. Working Principle of Cone Crusher:Cone crusher crushes materials by the working surface between the movable cone and fixed cone. So it is more advanced and efficiency than jaw crusher. The movable cone is supported by spherical bearing and fixed on an hanging erect shaft which is set in the eccentric sleeve, and the sleeve is set on the stopping and pushing bearing. The movable cone and erect shaft are drived by the eccentric shaft sleeve together. The eccentric shaft sleeve is driven by horizontal shaft and fimbriated gear, and the wheel of the conveyor belt is drived by motor through v-belts.The lower part of vertical shaft is installed in the eccentric sleeve. When the eccentric sleeve rotates, there is a conical surface lined out by the shaft. When the movable cone comes near the fixed cone, rocks are grinded into pieces, when the cone leaves, grinded materials is discharged from the diacharge hole. The fixed cone can be ascended or descended by adjusting setting to adjust the width of discharge hole, consequantly the output size is determined. ?Models:? PYB600 ~ PYB2200,? PYD600 ~ PYD2200,? PYZ900 ~ PYZ2200Max input(mm):? 35~300Adjusting range of output (mm):? 3~60Capacity(t/h):12~1000Electric motor power (kw):? 30~260Weight(t): 5~81.4Overall? dimensions (L×W×H) (mm): 2800×1300×1700, 3050×1640×2350, 4000×1900×2980, 4870×3800×4192, 5420×4300×4870 Notice: Any change of? technical data shall not be advised additionally.

  The Belt conveyer consist of standard parts, which are advanced and simple in structure, easy to maintain. Our? Belt conveyer equipment is adaptable for stationary and mobile crushing plants. They are widely used in mining, metallurgical and coal industry to transfer sandy or lump material, or packaged material. According to different transferring equipment, the transfer system can be one independently or multi-conveyers or combined with other transfer equipments. The belt conveyer can be installed horizontally or aslope to meet the needs of different transfer lines.? The belt conveyers produced by SJLC can be operated in the circumstance temperature range from minus twenty degrees centigrade to centigrade forty. The temperature of transferred material by this belt conveyer should be lower than fifty centigrate.? The types of the belt conveyers produced by SJLC are as follows:?1. Devided by Driving Method:? a. STD-Mechanical Drive? It's driven by cycloidal pinwheel reducer (with outdoor motor ) and chain-drive mechanism.? b. STDJ II Mechanical Drive Series .? It adopts upside-down reducer and belt-drive mechanize.? c. STD-Electric Rotor Drive Series? It's driven by electric rotor.?2. Divided by Installation Methods?a. Fixed Series? It's directly installed on foundation.? b. SDY-Portable Series? It's equipped with type for moving and slope adjusting capability, It can be Easily, it can be reely moved and adjusted by different transfer requirements? 3. Divided by Structures:? The belt conveyers produced by SJLC have three different structures.? a. U-steel ? b. Frame? c. Truss NOTE:? There are two kinds of conveyers, one equipped with repairing walkway while the other without. When ordering the machine, the customers should give us clear instruction.

  The ball mill is a key equipment to grind the crushed materials, and the ball mill is widely used in powder-making production line including cement, silicate, new-type building material, refractory material, fertilizer, ore dressing of ferrous metal and non-ferrous metal, glass ceramics, etc, and the ball mill can grind various ores and other materials with dry type and wet type. There are two kinds of ball mill, grate type and overfall type due to different ways of discharging material. Working Principle:The ball mill is a horizontal rotating device transmitted by the outer gear. The materials are transferred to the grinding chamber through the quill shaft uniformly. There are ladder liner and ripple liner and different specifications of steel balls in the chamber. The centrifugal force caused by rotation of barrel brings the steel balls to a certain height and impact and grind the materials. The ground materials are discharged through the discharging board thus the grinding process is finished. Model:Ф2200×5500Speed of bucket (r/min):21Weight of ball (t):30Size of feed opening (mm):≤25Size of outputting feed (mm):0.075-0.4Capacit (t/h):10-22Power (Kw):370

  Raymond grinder(Raymond mill) produced by our company is mainly used to grind non-inflammable and non-explosive materials with Moh’s hardness below 7 and moisture content below 6% such as barite, calcite, potash feldspar, talcum, marble, limestone, ceramic, glass, etc Raymond grinder can be used in mining, chemical industry, construction materials, metallurgy and so on. The final products can be adjusted freely from 100 mesh to 425 mesh. Working Principle of Raymond Grinder(Raymond mill):Firstly, raw material is crushed by jaw crusher to the size required, then elevated into a hopper from which the material is transported through the electro-magnetic vibrating feeder evenly and continuously into the grinding chamber for powder-processing. The rollers oscillate outward to press the ring because of the centrifugal force and the shovel scoops up the materials, send to the middle between the ring and rollers to accomplish the grinding.After grinding, the rough materials will be recycled by the air from the fan back into the grinding chamber for regrinding and the fine powders are blew into the cyclone and poured out through the output-powder pipe as the final products. The main features of raymond mill(raymond grinder)1.Three-dimensional structure , land-saving, easy to be a whole set2.The screen-passing rate can reach to 99%3.The transmission is steady and reliable;4.Centralized control for the electric system, convenient to operate Model:4R3216Roller Number:4Max.Feed Size(mm):25Fineness of product(mm):0.2-0.044Capacity(t/h):1.8-4.5Weight(t):15Main Frame Powder(kw):37 ?

  BREAK-DAY specializes in producing jaw crusher which is widely used in mining, quarry and material handling. Our company has been a manufacturer and exporter of crushers for decades.We have various models of jaw crusher. The jaw crusher is ideally suitable for primary and secondary crushing with low power consumption and easy maintenance. Every feature of this machine has been carefully designed to provide superior quality and performance. Jaw crusher is widely used for crushing various materials like stone, granite, trap rock, coke, coal, manganese ore, iron ore, emery, fused aluminum, oxide, fused calcium carbide, lime stone, quartzite, alloys, etc. Jaw crusher is recommended by leading consultants in this field and is used by hundreds of customers all over the world. The main features of jaw crusher :1.High reduction ratio.2.Simple structure3.Easy maintenance. Model:PE900x1200Feed Opening(mm):900x1200Max.Feed Size(mm):750Capacity(t/h):220-450Powder(KW):110-132