200 - 40,000 kilogram
40,001 - 999,999 kilogram
group nameAddition cure silicone rubber
Min Order200 kilogram
brand nameHong Ye silicone rubber
modelHY-E620 silicone rubber
payment methodT/T, L/C, Westem Union
update timeFri, 08 Nov 2013 18:11:22 GMT
white other color is no problem
State two part translucent
Sample available
feature 1 high tensile strength
feature 2 high copy times
feature 3 non-deformation
feature 4 no shrinkage
feature 5 easy for operation
mixing 1:1
feature 6 leading manufacture
Min Order200 kilogram
Silicone For tire mold reproduction
Description of silicone for tire mold
HY- E620 silicone is generally named two-components silicone
rubber, Part A and part B. It features an exceptional fluidity and good operability.
The mixing ratio is 1:1 mainly be suitable molds making
Typical Applications of silicone for tire mold
HY- E series addition molding silicone could be mainly used for making concrete
stones, wax molds, PU molds, resin molds, gypsum casting, candle molding and
chocolate , candy and any other FDA food product mold making,prototyping etc.
HY-E620 Silicone has been used for years to make tire pattern molds .
Characteristics of silicone for tire mold
*low shrinkage (less than 0.1% )
*high tensile and tear strength with high copy times
*easy for operation (mixing ratio at 1:1 /10:1)
*very good flow and easy for pouring operation
*Fast and non-shrink cure at room temperature which can be accelerated considerably by the application of heat
Technical Parameters of silicone for tire mold
Product | E-620 |
Appearance | Translucent |
Hardness(shore A) | 20±2 |
Mix ratio(A:B) | 1:1/10:1 |
Viscocity Part A(mPa.s) | 23000±2000 |
Viscocity Part B(mPa.s) | 3500±500 |
Tensile strength (kgf/cm2) | 45±5 |
Tear-strength (kN/m) | 20±2 |
Elongation(%) | 500±50 |
Pot life/working time (mins) | 30-40 |
Curing time/setting time (hrs) | 3-4hrs(25°C) 110-20mins(60°C) |
Shrinkage rate (%) | 0.1 |
(Please note: the above data for this product in 25°C temperature, 55percent humidity conditions, for reference. The accurate data is measured by customers when using.)
Operation instruction of silicone for tire mold :
1. Pls clear the model and tool totally before operation to prevent cure inhibition.
2.Weigh the two part correctly by electronic weight in two separate container .
3. Mixing the two part in 1:1/10:1 and stir part A and part B evenly in 2-3 minutes .
4.And get the mixture for vacuum-pumping for de-air the bubble in around 2-3
minutes . (If there is no vacuum machine, pls pour the mixture carefully and slowly
down the side of the mold frame so that less bubbles caused)
5. Enclose the product (the original model) with four plastic plates or wooden plates.
6. Clean your products and brush a layer of release agent(detergent or soap water) on
your product.
7. Pour the vacuumed mixture into the model frame from the side of the mold frame .
Notice of silicone for tire mold :
As our E-series silicone is platinum cure silicone , which is very easy to cause
cure inhibition , so pls do remember thoroughly clean the model and tool before
operation . Besides , pls avoid the liquid E-series silicone contact or mix with the
following material , otherwise the silicone won’t be cured :
1. Liquid condensation silicone ( condensation silicone not completely cured or organic
tin compounds )
2 .Sulphur, sulfide and sulfur rubber materials.
3. Amine compounds as well as contains the amine materials.
4 .Pewter solder flux.
SHELF LIFE of silicone for tire mold :
8-10 months when stored under 24°C in original unopened packages.
PACKAGE of silicone for tire mold :
If ratio is 1:1 :Packed in 20kg/pail + 20kg/pail and 200kg/pail + 200kg/pail.
If ratio is 10:1 :Packed in 20kg/pail + 2kg/pail and 200kg/pail + 20kg/pail.
Any other information needed , pls feel free to contact omiga
Tel:0086-755-89948294
mobile: 0086-18938867575
Or mail:hyjw(at)szrl(dot)net
Welcome to our website www dot szrl dot net
网络文化经营许可证:浙ICP备14006100号-11 2007-2024 Tradevv.com. All rights reserved.