200 - 40,000 kilogram
40,001 - 999,999 kilogram
group nameAddition cure silicone rubber
Min Order200 kilogram
brand nameHong Ye silicone rubber
modelE620 silicone rubber
payment methodT/T, L/C, Westem Union
update timeFri, 08 Nov 2013 18:13:38 GMT
white other color is no problem
State two part translucent
Sample available
feature 1 high tensile strength
feature 2 high copy times
feature 3 non-deformation
feature 4 no shrinkage
feature 5 easy for operation
mixing 1:1
feature 6 leading manufacture
Min Order200 kilogram
E620 Silicone Rubber For Tyre design
Description of E620 silicone rubber for tyre design
E620 addition molding silicone is generally named two-components silicone
rubber, Part A and part B. It features an exceptional fluidity and good operability.
The mixing ratio is 1:1 (10:1),mainly be suitable for making molds application.
Typical Applications of E620 silicone rubber for tyre design
E620 silicone rubber could be mainly used for making concrete
stones, wax molds, PU molds, resin molds, gypsum casting, candle molding and
chocolate , candy and any other FDA food product mold making,prototyping etc.
E620 Silicone Rubber has been used for years to make tyre design .
Characteristic of silicone rubber for tyre design
*low shrinkage (less than 0.1% )
*high tensile and tear strength with high copy times
*easy for operation (mixing ratio at 1:1 /10:1)
*very good flow and easy for pouring operation
*Fast and non-shrink cure at room temperature which can be accelerated considerably by the application of heat
Technical Parameters of silicone rubber for tyre design
Product | E620 |
Appearance | Translucent |
Hardness(shore A) | 20±2 |
Mix ratio(A:B) | 1:1/10:1 |
Viscocity Part A(mPa.s) | 23000±2000 |
Viscocity Part B(mPa.s) | 3500±500 |
Tensile strength (kgf/cm2) | 45±5 |
Tear-strength (kN/m) | 20±2 |
Elongation(%) | 500±50 |
Pot life/working time (mins) | 30-40 |
Curing time/setting time (hrs) | 3-4hrs(25°C) 110-20mins(60°C) |
Shrinkage rate (%) | 0.1 |
(Please note: the above data for this product in 25°C temperature, 55percent humidity conditions, for reference. The accurate data is measured by customers when using.)
Operation instruction of silicone rubber for tyre design
1. Pls clear the model and tool totally before operation to prevent cure inhibition.
2.Weigh the two part correctly by electronic weight in two separate container .
3. Mixing the two part in 1:1/10:1 and stir part A and part B evenly in 2-3 minutes .
4.And get the mixture for vacuum-pumping for de-air the bubble in around 2-3
minutes . (If there is no vacuum machine, pls pour the mixture carefully and slowly
down the side of the mold frame so that less bubbles caused)
5. Enclose the product (the original model) with four plastic plates or wooden plates.
6. Clean your products and brush a layer of release agent(detergent or soap water) on
your product.
7. Pour the vacuumed mixture into the model frame from the side of the mold frame .
Notice of silicone rubber for tyre design :
As our E-series silicone is platinum cure silicone , which is very easy to cause
cure inhibition , so pls do remember thoroughly clean the model and tool before
operation . Besides , pls avoid the liquid E-series silicone contact or mix with the
following material , otherwise the silicone won’t be cured :
1. Liquid condensation silicone ( condensation silicone not completely cured or organic
tin compounds )
2 .Sulphur, sulfide and sulfur rubber materials.
3. Amine compounds as well as contains the amine materials.
4 .Pewter solder flux.
SHELF LIFE of silicone rubber for tyre design :
8-10 months when stored under 24°C in original unopened packages.
PACKAGE of silicone rubber for tyre design :
Packed in 20kg/pail + 20kg/pail and 200kg/pail + 200kg/pail.
Any further information required ,pls feel free to contact omiga^
Tel : 0086-755-89948294
Mobile 0086-18938867575
skype;omigago
hyjw(at)szrl(dot)net
网络文化经营许可证:浙ICP备14006100号-11 2007-2024 Tradevv.com. All rights reserved.