200 - 40,000 kilogram
40,001 - 999,999 kilogram
group nameAddition cure silicone rubber
Min Order200 kilogram
brand nameHong Ye silicone rubber
modelHY- E635
payment methodT/T, L/C, Westem Union
update timeFri, 08 Nov 2013 18:19:14 GMT
Shaping Mode Silicone Mould
Product Material silicone rubber
Product liquid molding silicone
Appearance Translucent or white
Mixing Ratio 1:1
Operating time (Mins 25°C) 30 - 50
Curing time (Mins 25°C) 2-4h
Curing time (Mins 60°C) 4-5
Hardness (A°) 35±2
Density ( g/cm 3 ) 1.08
Viscosity (CS) (After mixed) 10000 ± 2000
Tear-strength (kgf /cm2 ) 15 ± 2
Elongation-break(%) 350 ± 50
Min Order200 kilogram
Addition cured silicone rubber for keyboard laminating
HY- E635# Addition cured silicone rubber
Description of addition cured silicone rubber for keyboard laminating
HY- E635# addition molding silicone is generally named two-components silicone rubber, Part A is a flowable liquid, part B is the curing agent. It features an exceptional fluidity and good operability. The mixing ratio is 1:1,mainly be suitable for making FDA molds application.
Applications of addition cured silicone rubber for keyboard laminating
HY- E635# addition molding silicone could be mainly used for making concrete stones, precision molds, PU molds, prototyping,for life casting, fabric finishing, seal for electronic components and solar circuit board, trademark decoration. etc.
Technique Data of HY-E635# Addition cured silicone rubber
Model | HY-E635# |
Appearance | Translucent or white |
Mixing Ratio | 1:1 |
Operating time (Mins 25°C) | 30 - 50 |
Curing time (Mins 25°C) | 2-4h |
Curing time (Mins 60°C) | 4-5 |
Hardness (A°) | 35±2 |
Density ( g/cm 3 ) | 1.08 |
Viscosity (CS) (Part A) | 30000 ± 5000 |
Viscosity (CS) (Part B) | 5000 ± 500 |
Viscosity (CS) (After mixed) | 10000 ± 2000 |
Tensile-strength( kgf /cm2 ) | 100 ± 20 |
Tear-strength (kgf /cm2 ) | 15 ± 2 |
Elongation-break(%) | 350 ± 50 |
Retractility(%) | ≤0.1 |
OPERRATING INSTRUCTION of HY-E635# Addition cured silicone rubber:
1. Stir part A and part B with right mixing ratio evenly. And get the mixture for vacuum-pumping. (If there is no vacuumizer, you can just pour the mixture slowly from the corner so that less bubbles caused)
2. Enclose the product (the original model) with four plastic plates or wooden plates.
3. Clean your products and brush a layer of release agent(detergent or soap water) on your product.
4. Pour the mixture with correct mixing ratio into the model frame.
After about 2-4 hours, when the silicone cured, get out the original model, and there you get a finished addition cured silicone mold .
Any question about Additional silicone rubber please feel free to contact Sarah
Tel:0086-755-89948019
Fax:0086-755-89948030
Mob:0086-13620974715
网络文化经营许可证:浙ICP备14006100号-11 2007-2024 Tradevv.com. All rights reserved.