200 - 40,000 kilogram
40,001 - 999,999 kilogram
group nameelectronic potting silicone rubber
Min Order200 kilogram
brand nameHong Ye silicone rubber
modelHY-9315# silicone rubber
payment methodT/T, L/C, Westem Union
update timeFri, 08 Nov 2013 20:00:57 GMT
Appearance Transparent fluid Colorless and transparent fluid liquid
Viscosity cP 600±200 1800±200
A:B(w/w) 1:1
Pot life min 3h
Curing time (80℃)min 20
Curing time (25℃) min 480
HardnessShore A 15
Thermal conductivity w/mK ≥0.2
Linear expansion Coefficient m/mK ≤2.2*0.0001
Model HY-9315
Min Order200 kilogram
gray electronice potting compoud silicone for street lamp
Product Features gray electronice potting compoud silicone for street lamp
HY-9315 is a kind of two-component electronic encapsulants with low viscosity with flame Resistance and thermal conductivity. It can get cured under room temperature or heated. The higher the temperature is, the faster the curing speed will be. The raw material with higher purity, does not contain any polar compounds and does not produce any By-products, so it can remain the better electrical performance in the hard conditions. It can be applied to the surface of olycarbonate, PP, ABS, PVC and metal material, and also for Insulation, moisture-proof, waterproof, shockproof, electronic components, Typical uses for protection of module power supply and circuit board potting high-power electronic components which has high requirements for elimination of heat and high temperature resistance.
Technical Parameters gray electronice potting compoud silicone for street lamp
(Please note: the above data for this product in 25 °Ctemperature, 55 percent humidity)
Model Code | HY-9315 | |
Before Curing | Appearance | A: Transparent fluid B: Colorless and transparent fluid liquid |
Viscosity cP | A: 600±200 B: 1800±200 | |
Operating Performance | A:B(w/w) | 1:1 |
Mixing Ratio cP | 800~1200 | |
Pot life min | 3h | |
Curing time (25°C) min | 480(could be cured both at room temperature and cured by heating.20mins at 80-100°C is suggested) | |
Curing time (80°C)min | 20 | |
After Curing | Hardness(Shore A) | 15 |
Thermal conductivity w/mK | ≥0.2 | |
Absolute degree Of dielectric kv/mm | ≥25 | |
Permittivity kv/mm | 3.0~3.3 | |
Volume Resistance Ω·cm | ≥1.0×1014 | |
Linear expansion Coefficient m/mK | ≤2.2×10-4 | |
Flame Resistance | UL94V1 |
TECHNICAL GUIDELINES gray electronice potting compoud silicone for street lamp
1, Typical Application
HY- 9315 could be applied to
- high powered electronics,
- DC/DC module and circuit board which requires heat dissipation and high temperature resistance.
-It can be broadly used for LED screen, Wind Power Generator, PCB substrate, etc.
Please put part A and part B in separate container and stir evenly before mixing the two part together.
2, Mixing Ratio: part A: part B = 1:1
3, Deaeration the mixture in vacuum pump under 0.08 MPa for 3-5 minutes. Then the mixture could be used for pouring.
4, Please note that the thickness of the silicone affects the curing time. If the silicone used is a little thick, then the curing time will be a little longer. The temperature also affects the curing time. When in lower temperature, we suggest customers appropriately heat the mixture to accelerate vulcanization. With temperature of 80~100°C, the silicone will cure in 15 minutes; while in 25°Croom temperature, the silicone will cure around 8 hours.
Notes
1.The following material may hinder the curing of HY-9315, so please use after the test. If necessary, please clean the application areas.
l Organotin compound or Condensation silicone with organotin.
l Sulphur, sulfide and sulfur rubber materials.
l Amine compounds as well as contains the amine materials.
l Pewters solder flux.
2. HY 9315 should be sealed storage.
The mixture should be used up disposably to avoid causing waste.
3. HY 9315 belongs to non-dangerous goods, but keep away from mouth and eyes.
4. When it gets stratified after a period of storage, Please mix it evenly before using, which does not affect the performance.
PACKAGE gray electronice potting compoud silicone for street lamp
40Kgs/pail as a set (Part A 20Kg + Part B 20Kg)
SHELF LIFE AND TRANSPORTATION gray electronice potting compoud silicone for street lamp
1. Twelve(12) months when stored at 25C in tightly closed original packages.
2. This kind of product is non-dangerous product, which could be transported as general chemicals.
3. Storage beyond the expired date does not necessarily mean that the product is no longer usable. In this case however, the properties required for the intended use must be checked for quality assurance reasons.
Any more information, pls feel free to contact Bella at any time.
Mobile: 0086-18938867572
Tel: 0086-755-89948006
Fax: 0086-755-89948030
Website: www (dot) szrl (dot) net
Email:hysi(at)szrl(dot)net
Skype: bellajiaqi
price for food-grade rtv silicone for food molds
网络文化经营许可证:浙ICP备14006100号-11 2007-2024 Tradevv.com. All rights reserved.