200 - 40,000 kilogram
40,001 - 999,999 kilogram
group nameRTV-2 silicone rubber for molds making
Min Order200 kilogram
brand nameHong Ye silicone rubber
modelHY628# silicone rubber
payment methodT/T, L/C, Westem Union
update timeSat, 09 Nov 2013 12:52:32 GMT
Sample Free
Color White
Curing time 6-8
Mixing proportion of curing agent (%) 2%-3%
Operating time (hour 25 0C ) 0.5
Viscosity (CPS 25 0C) 18000-25000
Hardness (shore A) 28-30
Tensile-strength(kgf /cm2 ) 37
Tear-strength (kgf /cm) 26
Elongation-break(%) 500
Min Order200 kilogram
Liquid RTV silicone rubber for cornice molds making
1. Applications of Liquid RTV silicone rubber for cornice molds making:
Hongye liquid silicone rubber can be used to cast a variety of materials including wax, gypsum, low melt alloys/metals and urethane, epoxy or polyester resins.
The following mouldings can be reproduced and cast by Silicone Rubber:architectural bracket mouldings,
decorative garden resin statue mouldings, gypsum plaster ornament mouldings, cornices, round corners, corbels mouldings, ceiling roses, medallion mouldings, pilaster and balustrade mouldings, art sculpture mouldings, quick prototyping, precision castings, art sculpture molds, landscape mouldings, precast stone mouldings and so on.
2. Features of Liquid RTV silicone rubber for cornice molds making:
Liquid Silicon rubber for mold making is white or red flowing liquid with general hardness of 22-50A°after curing. Molding silicon rubber is a kind elastic silicon rubber mold which features with resistance to deformation, high-temperature, acid-alkali and expansion as well as high reproduction times, good tensile strength ,tear strength and elongation. Our curing agent is free charged.
3. Process operations of Liquid RTV silicone rubber for cornice molds making:
Room Temperature Vulcanization (RTV) rubber molds are the least expensive and fastest way to create about a dozen prototype parts. As shown in the figure below, even with undercuts, the part is able to be removed through distortion of the mold.
a. Process and prepare the model mold or the product to be duplicated,
b. Take certain amount of the silicon rubber, add 2-3% solid curing agent, and mix evenly and they are ready for use.
c. Once cured, the RTV is removed from the vat and separated from the pattern and parting line surface to yield the two halves of the molding tool. RTV air-cures, so that the cure time depends on the geometry, the RTV type, and the environment. Cure time can range from .5 to 40 hours. Aging of the mold after cure for up to three days can improve mold life.
4.Frequently asked questions of Liquid RTV silicone rubber for cornice molds making:
What should we do when the air bubbles appeared in the process of mold making ?
To handle this situation depends on different cases. Under the condition of an available vacuum pumping machine, mix the silicon rubber and curing agent evenly and then take it to vacuum chamber to deair. If without a vacuum pumping machine, reduce the amount of the curing agent properly. For example, change the mixing ratio of the silicon rubber and the curing agent from former 4% to 1%-2%. In this way, the pre-crosslinking time of silicon rubber will slow down, so the air in the mold will be eliminated gradually to reduce the air bubbles.
5.Package of Liquid RTV silicone rubber for cornice molds making:
6.Certifications of Liquid RTV silicone rubber for cornice molds making:
7.Our factory:
Any questions, please feel free to contact Mr Lucas:
TEL: 086-755-89212369
FAX: 086-755-89948030
MOBILE:086-18898736056
E-mail: hysj(at)szrl(dot)net
You can also send me E-mail by scanning QR Bar Code below:
网络文化经营许可证:浙ICP备14006100号-11 2007-2024 Tradevv.com. All rights reserved.