ShenZhen Best Electronics Co.,Ltd

Micro/Miniature Switch with 0.3+/-0.1mm Travel and 3kg Stem Strength

2008-12-9 18:27:17

]]>General specification:

Scope: this specification covers the requirements for single key switches which have no key top
Operating temperature range: -20-70 degree Celsius
Storage temperature range: -20-80 degree Celsius
Actuating force: 100-260 +/-30gf
Travel: 0.3+/-0.1mm
Stem strength: 3kg
Contact resistance: 50m ohms maximum
Insulation resistance: 100m ohms maximum
Dielectric with standing: there shall be no breakdown

Tact/Micro Switch with 3Kgf Stem Strength and 0.3 ±0.1mm Travel

2008-12-9 18:28:56

]]>

Actuating force: 100 to 260 ±30gf

Travel: 0.3 ±0.1mm

Stem strength: 3Kgf

Contact resistance: 50m ohms maximum

Insulation resistance: 100m ohms maximum

Dielectric withstanding: there shall be no breakdown

Operating temperature range: -20 to 70 degrees Celsius (normal humidity, normal press)

Storage temperature range: -20 to 80 degrees Celsius (normal humidity, normal press)

Scope: specification covers the requirements for single key switches which have no key top (tact switches, mechanical contact)

Micro/Miniature Switch with 50m Ohms Contact Resistance and 100m Ohms Insulation Resistance

2008-12-9 18:30:20

]]>General specification:

Scope: this specification covers the requirements for single key switches which have no key top
Operating temperature range: -20-70 degree Celsius
Storage temperature range: -20-80 degree Celsius
Actuating force: 100-260 +/-30gf
Travel: 0.3+/-0.1mm
Stem strength: 3kg
Contact resistance: 50m ohms maximum
Insulation resistance: 100m ohms maximum
Dielectric with standing: there shall be no breakdown

Phone Jack with 50m Ohms Insulation Resistance and 50m Ohms Contact Resistance

2008-12-9 18:32:21

]]>

Electrical characteristics:

Rated power: DC 12V, 1A
Contact resistance: measurement shall be made at with small current 1000Hz(1A maximum)
Insulation resistance: a voltage of 500V DC shall be applied for 1 minute after which measurement shall be made
Dielectric strength: 500V AC(50 Hz-60Hz) for 1 minute
Trip current: 2mA

Endurance characteristics:

Soldering heat test: the terminal for a printed circuit board
Temperature of solder: 260+/-
Dip time: 5±1 seconds

The terminal for a lead wire:

Temperature of solder: 350±10
Dip time: 3±1 seconds

Cold: the jack shall be stored for 96 hours at a temperature of -25±3 immediately after which measurement shall be made

Dry heat: the jack shall be stored for 96 hours at a temperature of 70±2 immediately after which measurement shall be made

Contact resistance: 50m ohms maximum

Insulation resistance: 50m ohms minimum

Contact pressure: 0.5N(50gf) minutes

Insertion force: 3-30N(0.3-3.0kgf)

Withdrawal force: 3-30N(0.3-3.0kgf)

Phone Jack, with Maximum Contact Resistance of 50m Ohms

2008-12-9 18:33:50

]]>

Electrical characteristics:

Rated power: DC 12V, 1A

Contact resistance: measurement shall be made at with small current 1,000Hz (1A Max.)

Insulation resistance: a voltage of 500V DC shall be applied for 1 minute after which measurement shall be made

Dielectric strength: 500V AC (50 to 60Hz) for 1 minute, trip current: 2mA

Endurance characteristics:

Soldering heat test: the terminal for a printed circuit board:

Temperature of solder: 260 +/-℃

Dip time: 5 +/-1 seconds

The terminal for a lead wire:

Temperature of solder: 350 +/-10 deg.

Dip time: 3 +/-1 seconds

Cold: the jack shall be stored for 96 hours at a temperature of -25 +/-3 deg. immediately after which measurement shall be made

Dry heat: the jack shall be stored for 96 hours at a temperature of 70 +/-2 deg. immediately after which measurement shall be made

Contact resistance: 50m Ohms Max.

Insulation resistance: 50m Ohms Min.

Contact pressure: 0.5N (50gf) Min.

Insertion force: 3 to 30N (0.3 to 3.0Kgf)

Withdrawal force: 3 to 30N (0.3 to 3.0Kgf)

Phone Jack, with Maximum Contact Resistance of 50m Ohms

Phone Jack with 3-30N Insertion Force and 3-30N Withdrawal Force

2008-12-9 18:35:02

]]>

Electrical characteristics:

Rated power: DC 12V, 1A
Contact resistance: measurement shall be made at with small current 1,000Hz(1A maximum)
Insulation resistance: a voltage of 500V DC shall be applied for 1 minute after which measurement shall be made
Dielectric strength: 500V AC(50Hz-60Hz) for 1 minute
Trip current: 2mA

Endurance characteristics:

Soldering heat test: the terminal for a printed circuit board
Temperature of solder: 260+/-
Dip time: 5±1 seconds

The terminal for a lead wire:

Temperature of solder: 350±10
Dip time: 3±1 seconds

Cold: the jack shall be stored for 96 hours at a temperature of -25±3 immediately after which measurement shall be made

Dry heat: the jack shall be stored for 96 hours at a temperature of 70±2 immediately after which measurement shall be made

Contact resistance: 50m ohms maximum

Insulation resistance: 50m ohms minimum

Contact pressure: 0.5N(50gf) minutes

Insertion force: 3-30N(0.3-3.0kgf)

Withdrawal force: 3-30N(0.3-3.0kgf)

Phone Jack with Ratings of DC 12V, 1A and Trip Current of 2mA

2008-12-9 18:36:15

]]>

Electrical characteristics:

Rated power: DC 12V, 1A

Contact resistance: measurement shall be made at with small current 1,000Hz (1A max.)

Insulation resistance: a voltage of 500V DC shall be applied for 1 minute after which measurement shall be made

Dielectric strength: 500V AC (50 to 60Hz) for 1 minute, trip current: 2mA

Endurance characteristics:

Soldering heat test: the terminal for a printed circuit board:

Temperature of solder: 260 +/-℃

Dip time: 5 +/-1 second

The terminal for a lead wire:

Temperature of solder: 350 +/-10 deg.

Dip time: 3 +/-1 second

Cold: the jack shall be stored for 96 hours at a temperature of -25 +/-3 deg. immediately after which measurement shall be made

Dry heat: the jack shall be stored for 96 hours at a temperature of 70 +/-2 deg. immediately after which measurement shall be made

Contact resistance: 50m Ohm max.

Insulation resistance: 50m Ohm min.

Contact pressure: 0.5N (50gf) min.

Insertion force: 3 to 30N (0.3 to 3.0Kgf)

Withdrawal force: 3 to 30N (0.3 to 3.0Kgf)

Phone Jack with 50m Ohms Contact and Insulation Resistance

2008-12-9 18:37:27

]]>

Electrical characteristics:

Rated power: DC 12V, 1A
Contact resistance: measurement shall be made at with small current 1,000Hz(1A maximum)
Insulation resistance: a voltage of 500V DC shall be applied for 1 minute after which measurement shall be made
Dielectric strength: 500V AC(50 Hz-60Hz) for 1 minute
Trip current: 2mA

Endurance characteristics:

Soldering heat test: the terminal for a printed circuit board
Temperature of solder: 260+/-
Dip time: 5±1 seconds

The terminal for a lead wire:

Temperature of solder: 350+/-10
Dip time: 3±1 seconds

Cold: the jack shall be stored for 96 hours at a temperature of -25±3 immediately after which measurement shall be made

Dry heat: the jack shall be stored for 96 hours at a temperature of 70±2 immediately after which measurement shall be made

Contact resistance: 50m ohms maximum

Insulation resistance: 50m ohms minimum

Contact pressure: 0.5N(50gf) minutes

Insertion force: 3-30N(0.3-3.0Kgf)

Withdrawal force: 3-30N(0.3-3.0Kgf)

Phone Jack with DC 12V and 1A Rated Power

2008-12-9 18:38:27

]]>

Electrical characteristics:

Rated power: DC 12V, 1A
Contact resistance: measurement shall be made at with small current 1000Hz(1A maximum)
Insulation resistance: a voltage of 500V DC shall be applied for 1 minute after which measurement shall be made
Dielectric strength: 500V AC(50Hz-60Hz) for 1 minute
Trip current: 2mA

Endurance characteristics:

Soldering heat test: the terminal for a printed circuit board
Temperature of solder: 260+/-
Dip time: 5±1 seconds

The terminal for a lead wire:

Temperature of solder: 350±10
Dip time: 3±1 seconds

Cold: the jack shall be stored for 96 hours at a temperature of -25±3 immediately after which measurement shall be made

Dry heat: the jack shall be stored for 96 hours at a temperature of 70±2 immediately after which measurement shall be made

Contact resistance: 50m ohms maximum

Insulation resistance: 50m ohms minimum

Contact pressure: 0.5N(50gf) minutes

Insertion force: 3-30N(0.3-3.0kgf)

Withdrawal force: 3-30N(0.3-3.0kgf)

Phone Jack with 3-30N Withdrawal Force and 3-30N Insertion Force

2008-12-9 18:39:31

]]>

Electrical characteristics:

Rated power: DC 12V, 1A
Contact resistance: measurement shall be made at with small current 1,000Hz(1A maximum)
Insulation resistance: a voltage of 500V DC shall be applied for 1 minute after which measurement shall be made
Dielectric strength: 500V AC(50Hz-60Hz) for 1 minute
Trip current: 2mA

Endurance characteristics:

Soldering heat test: the terminal for a printed circuit board
Temperature of solder: 260+/-
Dip time: 5±1 seconds

The terminal for a lead wire:

Temperature of solder: 350±10
Dip time: 3±1 seconds

Cold: the jack shall be stored for 96 hours at a temperature of -25±3 immediately after which measurement shall be made

Dry heat: the jack shall be stored for 96 hours at a temperature of 70±2 immediately after which measurement shall be made

Contact resistance: 50m ohms maximum

Insulation resistance: 50m ohms minimum

Contact pressure: 0.5N(50gf) minutes

Insertion force: 3-30N(0.3-3.0kgf)

Withdrawal force: 3-30N(0.3-3.0kgf)

Phone Jack with Insulation Resistance of 50m Ohms

2008-12-9 18:40:37

]]>

Electrical characteristics:

Rated power: 12V DC/1A

Contact resistance: measurement shall be made at with small current 1000Hz (1A maximum)

Insulation resistance: A voltage of 500V DC shall be applied for 1 minute after which measurement shall be made

Dielectric strength: 500V AC (50 to 60Hz) for 1 minute

Trip current: 2mA

Endurance characteristics:

Soldering heat test: terminal for a printed circuit board

Temperature of solder: +/- 260 degrees Celsius

Dip time: 5 +/- 1 seconds

The terminal for a lead wire:

Temperature of solder: 350 +/- 10 degrees Celsius

Dip time: 3 +/- 1 seconds

Cold: the jack shall be stored for 96 hours at a temperature of -25 +/- 3 degrees Celsius immediately after which measurement shall be made

Dry heat: the jack shall be stored for 96 hours at a temperature of 70 +/- 2 degrees Celsius immediately after which measurement shall be made

Contact resistance: 50m Ohms

Insulation resistance: 50m Ohms

Contact pressure: 0.5N (50gf)

Insertion force: 3 to 30N (0.3 to 3.0Kgf)

Withdrawal force: 3 to 30N (0.3 to 3.0Kgf)

DC Power Jack with DC 12V and 1A Rating

2008-12-9 18:41:47

]]>

Electronics characteristics:

Rating: DC 12V, 1A
Contact resistance: 1kHz measured at small current (1A or less)
Insulation resistance: a voltage of 500V DC shall be applied for a minute, and between conductors which should not make contact under normal conditions after which measurement shall be made
Dielectric strength: between conductors which should not make contact under normal conditions 500V AC (50-60Hz) for 1 minute (trip current 2mA)

Endurance characteristics:

Solder ability: the terminals shall be dipped into soldering flux and shall be immersed into molten solder of 230±5 degrees for a period 3±0.5 seconds

Resistance to soldering heat:

Solder temperature: 350±10
Immersion depth: 2±0.5mm
Immersion time: 3±0.5 seconds
By a solder iron to have capacity of 60W

Cold: the jack shall be stored at a temperature of -40±2 for 96 hours

It shall be subjected to the controlled recovery conditions for 0.5 hours after which measurement shall be made

Dry heat: the jack shall be stored at a temperature of -70±2 for 96 hours

It shall be subjected to the controlled recovery conditions for 0.5 hours after which measurement shall be made

Humidity: the pin jack shall be subject to 90%-95%RH, 40±2 for 96 hours, and shall be conditioned at room ambient conditions for a period of 30 minutes

DC Power Jack with 3±0.5 seconds Immersion Time and 2±0.5mm Immersion Depth

2008-12-9 18:42:53

]]>

Electronics characteristics:

Rating: DC12V, 1A
Contact resistance: 1kHz measured at small current (1A or less)
Insulation resistance: a voltage of 500V DC shall be applied for a minute, and between conductors which should not make contact under normal conditions after which measurement shall be made
Dielectric strength: between conductors which should not make contact under normal conditions 500V AC (50-60Hz) for 1 minute (trip current 2mA)

Endurance characteristics:

Solder ability: the terminals shall be dipped into soldering flux and shall be immersed into molten solder of 230±5 degrees for a period 3±0.5 seconds

Resistance to soldering heat:

Solder temperature: 350±10
Immersion depth: 2±0.5mm
Immersion time: 3±0.5 seconds
By a solder iron to have capacity of 60W

Cold: the jack shall be stored at a temperature of -40±2 for 96 hours

It shall be subjected to the controlled recovery conditions for 0.5 hours after which measurement shall be made

Dry heat: the jack shall be stored at a temperature of -70±2 for 96 hours

It shall be subjected to the controlled recovery conditions for 0.5 hours after which measurement shall be made

Humidity: the pin jack shall be subject to 90%-95%RH, 40±2 for 96 hours, and shall be conditioned at room ambient conditions for a period of 30 minutes

DC Power Jack with 500V AC Dielectric Strength and 350±10 Solder Temperature

2008-12-9 18:44:34

]]>

Electronics characteristics:
- Rating: DC 12V, 1A
- Contact resistance: 1kHz measured at small current (1A or less)
- Insulation resistance: a voltage of 500V DC shall be applied for a minute, and between conductors which should not make contact under normal conditions after which measurement shall be made
- Dielectric strength: between conductors which should not make contact under normal conditions 500V AC (50-60Hz) for 1 minute (trip current 2mA)
Endurance characteristics:
- Solder ability: the terminals shall be dipped into soldering flux and shall be immersed into molten solder of 230±5 degrees for a period 3±0.5 seconds
Resistance to soldering heat:
- Solder temperature: 350+/-10
- Immersion depth: 2±0.5mm
- Immersion time: 3±0.5 seconds
- By a solder iron to have capacity of 60W
Cold: the jack shall be stored at a temperature of -40±2 for 96 hours
It shall be subjected to the controlled recovery conditions for 0.5 hours after which measurement shall be made
Dry heat: the jack shall be stored at a temperature of -70±2 for 96 hours
It shall be subjected to the controlled recovery conditions for 0.5 hours after which measurement shall be made
Humidity: the pin jack shall be subject to 90%-95%RH, 40±2 for 96 hours, and shall be conditioned at room ambient conditions for a period of 30 minutes

DC Power Jack with 350±10 Solder Temperature and 500V AC Dielectric Strength

2008-12-9 18:45:36

]]>

Electronics characteristics:

Rating: DC 12V, 1A
Contact resistance: 1kHz measured at small current (1A or less)
Insulation resistance: a voltage of 500V DC shall be applied for a minute, and between conductors which should not make contact under normal conditions after which measurement shall be made
Dielectric strength: between conductors which should not make contact under normal conditions 500V AC (50-60Hz) for 1 minute (trip current 2mA)

Endurance characteristics:

Solder ability: the terminals shall be dipped into soldering flux and shall be immersed into molten solder of 230±5 degrees for a period 3±0.5 seconds

Resistance to soldering heat:

Solder temperature: 350+/-10
Immersion depth: 2±0.5mm
Immersion time: 3±0.5 seconds
By a solder iron to have capacity of 60W

Cold: the jack shall be stored at a temperature of -40±2 for 96 hours

It shall be subjected to the controlled recovery conditions for 0.5 hours after which measurement shall be made

Dry heat: the jack shall be stored at a temperature of -70±2 for 96 hours

It shall be subjected to the controlled recovery conditions for 0.5 hours after which measurement shall be made

Humidity: the pin jack shall be subject to 90%-95%RH, 40±2 for 96 hours, and shall be conditioned at room ambient conditions for a period of 30 minutes

DC Power Jack with 2±0.5mm Immersion Depth

2008-12-9 18:46:40

]]>

Electronics characteristics:

Rating: DC12V, 1A
Contact resistance: 1kHz measured at small current (1A or less)
Insulation resistance: a voltage of 500V DC shall be applied for a minute, and between conductors which should not make contact under normal conditions after which measurement shall be made
Dielectric strength: between conductors which should not make contact under normal conditions 500V AC (50-60Hz) for 1 minute (trip current 2mA)

Endurance characteristics:

Solder ability: the terminals shall be dipped into soldering flux and shall be immersed into molten solder of 230±5 degrees for a period 3±0.5 seconds

Resistance to soldering heat:

Solder temperature: 350±10
Immersion depth: 2±0.5mm
Immersion time: 3±0.5 seconds
By a solder iron to have capacity of 60W

Cold: the jack shall be stored at a temperature of -40±2 for 96 hours

It shall be subjected to the controlled recovery conditions for 0.5 hours after which measurement shall be made

Dry heat: the jack shall be stored at a temperature of -70±2 for 96 hours

It shall be subjected to the controlled recovery conditions for 0.5 hours after which measurement shall be made

Humidity: the pin jack shall be subject to 90%-95%RH, 40±2 for 96 hours, and shall be conditioned at room ambient conditions for a period of 30 minutes

DC Power Jack with 1A and 12DC V Rating

2008-12-9 18:47:39

]]>

Electronics characteristics:

Rating: DC 12V, 1A
Contact resistance: 1kHz measured at small current (1A or less)
Insulation resistance: a voltage of 500V DC shall be applied for a minute, and between conductors which should not make contact under normal conditions after which measurement shall be made
Dielectric strength: between conductors which should not make contact under normal conditions 500V AC (50-60Hz) for 1 minute (trip current 2mA)

Endurance characteristics:

Solder ability: the terminals shall be dipped into soldering flux and shall be immersed into molten solder of 230±5 degrees for a period 3±0.5 seconds

Resistance to soldering heat:

Solder temperature: 350±10
Immersion depth: 2±0.5mm
Immersion time: 3±0.5 seconds
By a solder iron to have capacity of 60W

Cold: the jack shall be stored at a temperature of -40±2 for 96 hours

It shall be subjected to the controlled recovery conditions for 0.5 hours after which measurement shall be made

Dry heat: the jack shall be stored at a temperature of -70±2 for 96 hours

It shall be subjected to the controlled recovery conditions for 0.5 hours after which measurement shall be made

Humidity: the pin jack shall be subject to 90%-95%RH, 40±2 for 96 hours, and shall be conditioned at room ambient conditions for a period of 30 minutes

DC Power Jack with 2±0.5mm Immersion Depth and 3±0.5 Seconds Immersion Time

2008-12-9 18:48:37

]]>

Electronics characteristics:

Rating: 12DC V, 1A
Contact resistance: 1kHz measured at small current (1A or less)
Insulation resistance: a voltage of 500V DC shall be applied for a minute, and between conductors which should not make contact under normal conditions after which measurement shall be made
Dielectric strength: between conductors which should not make contact under normal conditions 500V AC (50-60Hz) for 1 minute (trip current 2mA)

Endurance characteristics:

Solder ability: the terminals shall be dipped into soldering flux and shall be immersed into molten solder of 230±5 degrees for a period 3±0.5 seconds

Resistance to soldering heat:

Solder temperature: 350±10
Immersion depth: 2±0.5mm
Immersion time: 3±0.5 seconds
By a solder iron to have capacity of 60W

Cold: the jack shall be stored at a temperature of -40±2 for 96 hours

It shall be subjected to the controlled recovery conditions for 0.5 hours after which measurement shall be made

Dry heat: the jack shall be stored at a temperature of -70±2 for 96 hours

It shall be subjected to the controlled recovery conditions for 0.5 hours after which measurement shall be made

Humidity: the pin jack shall be subject to 90%-95%RH, 40±2 for 96 hours, and shall be conditioned at room ambient conditions for a period of 30 minutes

DC Power Jack with Rating of 12V DC, 1A

2008-12-9 18:49:37

]]>

Electronics characteristics:

Rating: DC 12V, 1A

Contact resistance: 1kHz measured at small current (1A or less)

Insulation resistance: a voltage of 500V DC shall be applied for a minute, between conductors which should not make contact under normal conditions after which measurement shall be made

Dielectric strength: between conductors which should not make contact under normal conditions. 500V AC (50 to 60Hz) for 1 minimum (trip current 2mA)

Endurance characteristics:

Solderability: the terminals shall be dipped into soldering flux, and shall be immersed into molten solder of 230 degrees +/- 5 degrees for a period 3+/-0.5 seconds

Resistance to soldering heat:

Solder temperature: 350 degrees C +/- 10 degrees C

Immersion depth: 2+/-0.5mm

Immersion time: 3+/-0.5 seconds

By a solder iron to have capacity of 60W

Cold: the jack shall be stored at a temperature of -40 degrees C +/- 2 degrees C for 96 hours. And then it shall be subjected to the controlled recovery conditions for 0.5 hours after which measurement shall be made

Dry Heat: the jack shall be stored at a temperature of -70 degrees C +/- 2 degrees C for 96 hours. And then it shall be subjected to the controlled recovery conditions for 0.5 hours after which measurement shall be made

Humidity: the pin jack shall be subject to 90% to 95%RH, 40 degrees C +/- 2 degrees C for 96 hours, and shall be conditioned at room ambient conditions for a period of 30 minutes

DC Power Jack with Voltage Rating of 12V DC

2008-12-9 18:50:42

]]>

Electronics characteristics:

Rating: DC12V, 1A

Contact resistance: 1kHz measured at small current (1A or less)

Insulation resistance: A voltage of 500V DC shall be applied for a minute, between conductors which should not make contact under normal conditions after which measurement shall be made

Dielectric strength: between conductors which should not make contact under normal conditions. 500V AC (50 to 60Hz) for 1 minimum (trip current 2mA)

Endurance characteristics:

Solderability: the terminals shall be dipped into soldering flux, and shall be immersed into molten solder of 230degree+/-5degree for a period 3+/-0.5 seconds

Resistance to soldering heat:

Solder temperature: 350 degrees C +/- 10 degrees C

Immersion depth: 2+/-0.5mm

Immersion time: 3+/-0.5 seconds

By a solder iron to have capacity of 60W

Dry heat: the jack shall be stored at a temperature of -70 degrees C +/- 2 degrees C for 96 hours. And then it shall be subjected to the controlled recovery conditions for 0.5 hours after which measurement shall be made

Humidity: the pin jack shall be subject to 90% to 95% RH, 40 degrees C +/- 2 degrees C for 96 hours, and shall be conditioned at room ambient conditions for a period of 30 minutes

Trimmer Resistor with 500Ω to 4.7MΩ Resistance Range and 400g.cm Stopper Strength

2008-12-9 18:52:57

]]>

Mechanical characteristics:

Total rotational angle: 235°±5°
Rotational torque: 20 to 200 gf.cm
Stopper strength: 400g.cm (minimum)

Electrical characteristics:

Total resistance range: 500Ω to 4.7MΩ
Total resistance tolerance: 500Ω1MΩ: ±20%, other: ±30%
Resistance taper: linear (B)
Power rating (at 70°C): ≤0.25W
Maximum operating voltage: 250V AC
Residual resistance: R<10kΩ: 10Ω (maximum) 10kΩ: 3% (minimum)

Endurance:

Rotation life: 500 to 10,000 cycles
Temperature characteristic: 20 to 70°ΔR<±8%R
Moisture characteristic: 40°C 95% 5 hoursΔ(R/R) R≤±15%
Soldering heat characteristic: 260°C (maximum) at 3 seconds

Trimmer Resistor with Linear Taper and 260°±10° Total Rotational Angle

2008-12-9 18:54:35

]]>

Mechanical characteristics:

Total rotational angle: 260°±10°
Rotational torque: 40 to 250 gf.cm
Stopper strength: ≥1kgf.cm

Electrical characteristics:

Total resistance range: 100Ω to 4.7MΩ
Total resistance tolerance: 500Ω1MΩ: ±20%, other: ±30%
Resistance taper: linear (B)
Power rating (at 70°C): ≤0.25W
Maximum operating voltage: 250V AC
Residual resistance: R<10kΩ: 10Ω (maximum) 10kΩ: 3% (minimum)

Endurance:

Rotation life: 500 to 10,000 cycles
Temperature characteristic: 20 to 70°ΔR<±8%R
Moisture characteristic: 40°C 95% 5 hoursΔ(R/R) R≤±15%
Load characteristic: 40°C 95% 5 hoursΔ(R/R) R≤±15%
Soldering heat characteristic: 270°C (maximum) at 3 seconds

Trimmer Resistor with 5% Sliding Noise and 40 to 250 gf.cm Rotational Torque

2008-12-9 18:56:03

]]>

Mechanical characteristics:

Total rotational angle: 260°±10°
Rotational torque: 40 to 250 gf.cm
Stopper strength: ≥1kgf.cm

Electrical characteristics:

Total resistance range: 100Ω to 4.7MΩ
Total resistance tolerance: 500Ω1MΩ: ±20%, other: ±30%
Resistance taper: linear (B)
Power rating (at 70°C): ≤0.25W
Maximum operating voltage: 250V AC
Residual resistance: R<10kΩ: 10Ω (maximum) 10kΩ: 3% (minimum)
Endurance:
- Rotation life: 500 to 10,000 cycles
- Temperature characteristic: 20 to 70°ΔR<±8%R
- Moisture characteristic: 40°C 95% 5 hoursΔ(R/R) R≤±15%
- Load characteristic:
- Soldering heat characteristic: 270°C (maximum) at 3 seconds

Rotary Potentiometer, Rotation life: 500 Cycles-10,000 Cycles

2008-12-9 18:57:28

]]>

Total rotational angle: 260 degrees±, 10 degrees

Rotational torque: 40-250gf.cm

Stopper strenght: ≥1kgf.cm

Total resistance range: 100-4.7M

Total resistance tolerance: 500R1M: ±20W, other: ±30

Resistance taper: linear (B)

Power rating: 70≤0.25W

Maximum operating voltage: 250V AV

Resibual resistance: R10K: 10 maximum R≥ 10K: 3 min

Rotation life: 500 cycles-10,000 cycles

Temperature chracteristics: 20-70R± 8R

Moisture chracteristics: 40, 95, 5 hours (R/R) R≤±15

Load chracteristics: 40, 90, 5 hours (R/R) R≤±15

Soldering should be carried out within 3 secondsat a temperature of 270 degree celcius maximum

Rotary Potentiometer with Withstand Voltage of 101.3kPa/500V, 8.5kpa/315V

2008-12-9 18:58:58

]]>Characteristics:

Range of nominal resistance: 10 Ohms to 2M Ohms
Resistance tolerance: ±10%
Terminal resistance: 1%R or 2 Ohms
Contact resistance variation: 3%R or 3 Ohms
Insulation resistance: R1≥1G Ohms
Withstand voltage: 101.3kPa/500V, 8.5kpa/315V
Effective electrical travel: 210±100
Rated maximum power working voltage: 250V +70V 0.5W +125W
Temperature range: -55 to +125 degrees Celcius
TCR: ±250ppm
Temperature variation: R≤±2%RUab/UacR≤±1%
Collision: 390m/s², 4000uqw, R≤≥1%R
Vibration: 10 to 2000Hz, 0.75mm, 98m/s2, 6h
R≤±1%RUab/Uac≤±2%
Climate category: R≤±3%RR1≥100M
Electrical endurance: 70W, 0.5W, 1,000h, R≤±3%R
Mechanical endurance: 100cycles, R≤±3%R Steady damp-heat
R≤≥3%R, R1≥100M
Total mechanical travel: 2500±100
Starting torque: ≤20mNm
Stop torque: ≥50mN?m
Standard packaging: 50 pieces per tube

Precision Potentiometer with Stop Torque of ≥50mNm

2008-12-9 19:00:06

]]>Characteristics:

Range of nominal resistance: 10 Ohms to 2M Ohms
Resistance tolerance: ±10%
Terminal resistance: 1%R or 2 Ohms
Contact resistance variation: 3%R or 3 Ohms
Insulation resistance: R1≥1G Ohms
Withstand voltage: 101.3kPa/500V, 8.5kpa/315V
Effective electrical travel: 210±100
Rated maximum power working voltage: 250V +70V 0.5W +125W
Temperature range: -55 to +125 degrees Celcius
TCR: ±250ppm
Temperature variation: R≤±2%RUab/UacR≤±1%
Collision: 390m/s², 4000uqw, R≤≥1%R
Vibration: 10 to 2000Hz, 0.75mm, 98m/s2, 6h
R≤±1%RUab/Uac≤±2%
Climate category: R≤±3%RR1≥100M
Electrical endurance: 70W, 0.5W, 1,000h, R≤±3%R
Mechanical endurance: 100cycles, R≤±3%R Steady damp-heat
R≤≥3%R, R1≥100M
Total mechanical travel: 2500±100
Starting torque: ≤20mNm
Stop torque: ≥50mN?m
Standard packaging: 50 pieces per tube

Precision Potentiometer with TCR ±250ppm

2008-12-9 19:01:11

]]>Characteristics:

Range of nominal resistance: 10 Ohms to 2M Ohms
Resistance tolerance: ±10%
Terminal resistance: 1%R or 2 Ohms
Contact resistance variation: 3%R or 3 Ohms
Insulation resistance: R1≥1G Ohms
Withstand voltage: 101.3kPa/500V, 8.5kpa/315V
Effective electrical travel: 210±100
Rated maximum power working voltage: 250V +70V 0.5W +125W
Temperature range: -55 to +125 degrees Celcius
TCR: ±250ppm
Temperature variation: R≤±2%RUab/UacR≤±1%
Collision: 390m/s2,4000uqw, R≤≥1%R
Vibration: 10 - 2000Hz, 0.75mm, 98m/s2, 6h
R≤±1%RUab/Uac≤±2%
Climate category: R≤±3%RR1≥100M
Electrical endurance: 70W, 0.5W, 1000h, R≤±3%R
Mechanical endurance: 100cycles, R≤±3%R Steady damp-heat
R≤≥3%R, R1≥100M
Total mechanical travel: 2500±100
Starting torque: ≤20mNm
Stop torque: ≥50mN?m
Standard packaging: 50 pieces per tube

Cermet Potentiometer with Nominal Resistance of 10 to 2 Megaohms

2008-12-9 19:02:13

]]>

Characteristics:

Nominal resistance: 10 to 2 megaohms
Resistance tolerance: 10%
Terminal resistance: 1% R
Contact resistance variation: 3% R or 3
Insulation resistance: R1 1G
Withstand voltage: 101.3 kPa 500V, 8.5kpa315V
Effective electrical travel: 210 100

Environment Features:

Power working voltage: 250V +70,0.5W +125
Temperature range: -55 to +125 degrees Celsius
TCR: 250ppm
Temperature variation: R2 percent
Collision: 390m/s2,4000uqw ,1% R
Vibration: 10 to 2,000Hz; 0.75mm, 98m/s26h
Climate category: 3% RR1 100M
Electrical endurance: 70,0.5W 1,000hrs, R3 percent
Mechanical endurance: 100 cycles
Steady damp-heat

Physical Characteristics:

Total mechanical travel: 250 +- 10
Starting torque: 20mN.m
Stop torque: 50mN>m
Standard packaging: 50pcs per tube

Precision/Cermet/Trimmer Potentiometer, Variable Resistor Trimpots, Resistance Ranges 10 to 2M Ohms

2008-12-9 19:03:19

]]>Characteristics:

Range of nominal resistance: 10 to 2 M Ohms
Resistance tolerance: ±10%
Terminal resistance: 1% R or 2 Ohms
Contact resistance variation: 3% R or 3 Ohms
Insulation resistance: R1≥ 1G Ohms
Withstand voltage: 101.3kPa 500V, 8.5kpa 315V
Effective electrical travel: 210±100
Rated maximum power working voltage: 250V +70V 0.5W +125W
Temperature range: -55 to +125 degree celcius
TCR: ±250ppm
Temperature variation: R≤± 2% RUab/UacR≤ ±1%
Collision: 390m/s²,4000uqw, R≤≥1%R
Vibration: 10 to 2000Hz, 0.75mm, 98m/s², 6h
R≤± 1%RUab/Uac≤±2%
Climate category: R≤ ± 3% RR1≥ 100M
Electrical endurance: 70W, 0.5W, 1000h, R≤±3%R
Mechanical endurance: 100 cycles, R≤± 3%R steady damp-heat
R≤≥3%R, R1≥100M
Total mechanical travel: 2500±100
Starting torque: ≤20mNm
Stop torque: ≥50mN?m
Standard packaging: 50 pieces per tube

Precision Potentiometer with Nominal Resistance Range of 10 Ohms to 20M Ohms

2008-12-9 19:05:55

]]>Characteristics:

Range of nominal resistance: 10 Ohms to 2M Ohms
Resistance tolerance: ±10%
Terminal resistance: 1%R or 2 Ohms
Contact resistance variation: 3%R or 3 Ohms
Insulation resistance: R1≥1G Ohms
Withstand voltage: 101.3kPa/500V, 8.5kpa/315V
Effective electrical travel: 210±100
Rated maximum power working voltage: 250V +70V 0.5W +125W
Temperature range: -55 to +125 degrees Celcius
TCR: ±250ppm
Temperature variation: R≤±2%RUab/UacR≤±1%
Collision: 390m/s², 4000uqw, R≤≥1%R
Vibration: 10 to 2000Hz, 0.75mm, 98m/s2, 6h
R≤±1%RUab/Uac≤±2%
Climate category: R≤±3%RR1≥100M
Electrical endurance: 70W, 0.5W, 1,000h, R≤±3%R
Mechanical endurance: 100cycles, R≤±3%R Steady damp-heat
R≤≥3%R, R1≥100M
Total mechanical travel: 2500±100
Starting torque: ≤20mNm
Stop torque: ≥50mN?m
Standard packaging: 50 pieces per tube

Rotary Trimmer Potentiometer with Variable Resistor

2008-12-10 11:38:02

]]>

Electrical characteristics:

Total resistance: 100-5MΩ
Total resistance tolerance: ±20Ω
Ratings power: 0.1W
Resistance taper: taper B
Sliding noise: 150mV maximum

Taper: curve

Maximum power rating: 0.5W

Maximum working voltage: 250V

Mechanical characteristics:

Rotation angle: 260±10 degrees
Rotation torque: 5-35Nm
Stopper strength: ≥100Nm

Working temperature: 40 - 125 degree Celsius

Terminal strength: 30Nm

DC Power Jack with 1A and 12DC V Rating

2008-12-10 10:59:36

]]>

Electronics characteristics:

Rating: DC 12V, 1A
Contact resistance: 1kHz measured at small current (1A or less)
Insulation resistance: a voltage of 500V DC shall be applied for a minute, and between conductors which should not make contact under normal conditions after which measurement shall be made
Dielectric strength: between conductors which should not make contact under normal conditions 500V AC (50-60Hz) for 1 minute (trip current 2mA)

Endurance characteristics:

Solder ability: the terminals shall be dipped into soldering flux and shall be immersed into molten solder of 230±5 degrees for a period 3±0.5 seconds

Resistance to soldering heat:

Solder temperature: 350±10
Immersion depth: 2±0.5mm
Immersion time: 3±0.5 seconds
By a solder iron to have capacity of 60W

Cold: the jack shall be stored at a temperature of -40±2 for 96 hours

It shall be subjected to the controlled recovery conditions for 0.5 hours after which measurement shall be made

Dry heat: the jack shall be stored at a temperature of -70±2 for 96 hours

It shall be subjected to the controlled recovery conditions for 0.5 hours after which measurement shall be made

Humidity: the pin jack shall be subject to 90%-95%RH, 40±2 for 96 hours, and shall be conditioned at room ambient conditions for a period of 30 minutes

DC Power Jack with 2±0.5mm Immersion Depth

2008-12-10 11:05:01

]]>

Electronics characteristics:

Rating: DC12V, 1A
Contact resistance: 1kHz measured at small current (1A or less)
Insulation resistance: a voltage of 500V DC shall be applied for a minute, and between conductors which should not make contact under normal conditions after which measurement shall be made
Dielectric strength: between conductors which should not make contact under normal conditions 500V AC (50-60Hz) for 1 minute (trip current 2mA)

Endurance characteristics:

Solder ability: the terminals shall be dipped into soldering flux and shall be immersed into molten solder of 230±5 degrees for a period 3±0.5 seconds

Resistance to soldering heat:

Solder temperature: 350±10
Immersion depth: 2±0.5mm
Immersion time: 3±0.5 seconds
By a solder iron to have capacity of 60W

Cold: the jack shall be stored at a temperature of -40±2 for 96 hours

It shall be subjected to the controlled recovery conditions for 0.5 hours after which measurement shall be made

Dry heat: the jack shall be stored at a temperature of -70±2 for 96 hours

It shall be subjected to the controlled recovery conditions for 0.5 hours after which measurement shall be made

Humidity: the pin jack shall be subject to 90%-95%RH, 40±2 for 96 hours, and shall be conditioned at room ambient conditions for a period of 30 minutes

DC Power Jack with 2±0.5mm Immersion Depth and 3±0.5 Seconds Immersion Time

2008-12-10 11:00:58

]]>

Electronics characteristics:
- Rating: 12DC V, 1A
- Contact resistance: 1kHz measured at small current (1A or less)
- Insulation resistance: a voltage of 500V DC shall be applied for a minute, and between conductors which should not make contact under normal conditions after which measurement shall be made
- Dielectric strength: between conductors which should not make contact under normal conditions 500V AC (50-60Hz) for 1 minute (trip current 2mA)
Endurance characteristics:
- Solder ability: the terminals shall be dipped into soldering flux and shall be immersed into molten solder of 230±5 degrees for a period 3±0.5 seconds
Resistance to soldering heat:
- Solder temperature: 350±10
- Immersion depth: 2±0.5mm
- Immersion time: 3±0.5 seconds
- By a solder iron to have capacity of 60W
Cold: the jack shall be stored at a temperature of -40±2 for 96 hours
It shall be subjected to the controlled recovery conditions for 0.5 hours after which measurement shall be made
Dry heat: the jack shall be stored at a temperature of -70±2 for 96 hours
It shall be subjected to the controlled recovery conditions for 0.5 hours after which measurement shall be made
Humidity: the pin jack shall be subject to 90%-95%RH, 40±2 for 96 hours, and shall be conditioned at room ambient conditions for a period of 30 minutes

DC Power Jack with 350±10 Solder Temperature and 500V AC Dielectric Strength

2008-12-10 11:02:41

]]>

Electronics characteristics:

Rating: DC 12V, 1A
Contact resistance: 1kHz measured at small current (1A or less)
Insulation resistance: a voltage of 500V DC shall be applied for a minute, and between conductors which should not make contact under normal conditions after which measurement shall be made
Dielectric strength: between conductors which should not make contact under normal conditions 500V AC (50-60Hz) for 1 minute (trip current 2mA)

Endurance characteristics:

Solder ability: the terminals shall be dipped into soldering flux and shall be immersed into molten solder of 230±5 degrees for a period 3±0.5 seconds

Resistance to soldering heat:

Solder temperature: 350+/-10
Immersion depth: 2±0.5mm
Immersion time: 3±0.5 seconds
By a solder iron to have capacity of 60W

Cold: the jack shall be stored at a temperature of -40±2 for 96 hours

It shall be subjected to the controlled recovery conditions for 0.5 hours after which measurement shall be made

Dry heat: the jack shall be stored at a temperature of -70±2 for 96 hours

It shall be subjected to the controlled recovery conditions for 0.5 hours after which measurement shall be made

Humidity: the pin jack shall be subject to 90%-95%RH, 40±2 for 96 hours, and shall be conditioned at room ambient conditions for a period of 30 minutes

DC Power Jack with Rating of 12V DC, 1A

2008-12-10 14:09:27

]]>

Electronics characteristics:

Rating: DC 12V, 1A

Contact resistance: 1kHz measured at small current (1A or less)

Insulation resistance: a voltage of 500V DC shall be applied for a minute, between conductors which should not make contact under normal conditions after which measurement shall be made

Dielectric strength: between conductors which should not make contact under normal conditions. 500V AC (50 to 60Hz) for 1 minimum (trip current 2mA)

Endurance characteristics:

Solderability: the terminals shall be dipped into soldering flux, and shall be immersed into molten solder of 230 degrees +/- 5 degrees for a period 3+/-0.5 seconds

Resistance to soldering heat:

Solder temperature: 350 degrees C +/- 10 degrees C

Immersion depth: 2+/-0.5mm

Immersion time: 3+/-0.5 seconds

By a solder iron to have capacity of 60W

Humidity: the pin jack shall be subject to 90% to 95%RH, 40 degrees C +/- 2 degrees C for 96 hours, and shall be conditioned at room ambient conditions for a period of 30 minutes

Micro/Miniature Switch with 0.3+/-0.1mm Travel and 3kg Stem Strength

2008-12-11 16:53:14

]]>General specification:

Scope: this specification covers the requirements for single key switches which have no key top
Operating temperature range: -20-70 degree Celsius
Storage temperature range: -20-80 degree Celsius
Actuating force: 100-260 +/-30gf
Travel: 0.3+/-0.1mm
Stem strength: 3kg
Contact resistance: 50m ohms maximum
Insulation resistance: 100m ohms maximum
Dielectric with standing: there shall be no breakdown

Micro/Miniature Switch with 50m Ohms Contact Resistance and 100m Ohms Insulation Resistance

2008-12-10 10:51:17

]]>General specification:

Scope: this specification covers the requirements for single key switches which have no key top
Operating temperature range: -20-70 degree Celsius
Storage temperature range: -20-80 degree Celsius
Actuating force: 100-260 +/-30gf
Travel: 0.3+/-0.1mm
Stem strength: 3kg
Contact resistance: 50m ohms maximum
Insulation resistance: 100m ohms maximum
Dielectric with standing: there shall be no breakdown

Phone Jack with 3-30N Insertion Force

2008-12-11 16:50:56

]]>

Electrical characteristics:

Rated power: DC 12V, 1A
Contact resistance: measurement shall be made at with small current 1,000Hz(1A maximum)
Insulation resistance: a voltage of 500V DC shall be applied for 1 minute after which measurement shall be made
Dielectric strength: 500V AC(50Hz-60Hz) for 1 minute
Trip current: 2mA

Endurance characteristics:

Soldering heat test: the terminal for a printed circuit board
Temperature of solder: 260+/-
Dip time: 5±1 seconds

The terminal for a lead wire:

Temperature of solder: 350±10
Dip time: 3±1 seconds

Cold: the jack shall be stored for 96 hours at a temperature of -25±3 immediately after which measurement shall be made

Dry heat: the jack shall be stored for 96 hours at a temperature of 70±2 immediately after which measurement shall be made

Contact resistance: 50m ohms maximum

Insulation resistance: 50m ohms minimum

Contact pressure: 0.5N(50gf) minutes

Insertion force: 3-30N(0.3-3.0kgf)

Withdrawal force: 3-30N(0.3-3.0kgf)

Phone Jack with 3-30N Withdrawal Force and 3-30N Insertion Force

2008-12-10 14:07:20

]]>

Electrical characteristics:

Rated power: DC 12V, 1A
Contact resistance: measurement shall be made at with small current 1,000Hz(1A maximum)
Insulation resistance: a voltage of 500V DC shall be applied for 1 minute after which measurement shall be made
Dielectric strength: 500V AC(50Hz-60Hz) for 1 minute
Trip current: 2mA

Endurance characteristics:

Soldering heat test: the terminal for a printed circuit board
Temperature of solder: 260+/-
Dip time: 5±1 seconds

The terminal for a lead wire:

Temperature of solder: 350±10
Dip time: 3±1 seconds

Cold: the jack shall be stored for 96 hours at a temperature of -25±3 immediately after which measurement shall be made

Dry heat: the jack shall be stored for 96 hours at a temperature of 70±2 immediately after which measurement shall be made

Contact resistance: 50m ohms maximum

Insulation resistance: 50m ohms minimum

Contact pressure: 0.5N(50gf) minutes

Insertion force: 3-30N(0.3-3.0kgf)

Withdrawal force: 3-30N(0.3-3.0kgf)

Phone Jack with 50m Ohms Insulation Resistance and 50m Ohms Contact Resistance

2008-12-10 10:54:56

]]>

Electrical characteristics:

Rated power: DC 12V, 1A
Contact resistance: measurement shall be made at with small current 1000Hz(1A maximum)
Insulation resistance: a voltage of 500V DC shall be applied for 1 minute after which measurement shall be made
Dielectric strength: 500V AC(50 Hz-60Hz) for 1 minute
Trip current: 2mA

Endurance characteristics:

Soldering heat test: the terminal for a printed circuit board
Temperature of solder: 260+/-
Dip time: 5±1 seconds

The terminal for a lead wire:

Temperature of solder: 350±10
Dip time: 3±1 seconds

Cold: the jack shall be stored for 96 hours at a temperature of -25±3 immediately after which measurement shall be made

Dry heat: the jack shall be stored for 96 hours at a temperature of 70±2 immediately after which measurement shall be made

Contact resistance: 50m ohms maximum

Insulation resistance: 50m ohms minimum

Contact pressure: 0.5N(50gf) minutes

Insertion force: 3-30N(0.3-3.0kgf)

Withdrawal force: 3-30N(0.3-3.0kgf)

Phone Jack with DC 12V and 1A Rated Power

2008-12-10 10:57:55

]]>

Electrical characteristics:

Rated power: DC 12V, 1A
Contact resistance: measurement shall be made at with small current 1000Hz(1A maximum)
Insulation resistance: a voltage of 500V DC shall be applied for 1 minute after which measurement shall be made
Dielectric strength: 500V AC(50Hz-60Hz) for 1 minute
Trip current: 2mA

Endurance characteristics:

Soldering heat test: the terminal for a printed circuit board
Temperature of solder: 260+/-
Dip time: 5±1 seconds

The terminal for a lead wire:

Temperature of solder: 350±10
Dip time: 3±1 seconds

Cold: the jack shall be stored for 96 hours at a temperature of -25±3 immediately after which measurement shall be made

Dry heat: the jack shall be stored for 96 hours at a temperature of 70±2 immediately after which measurement shall be made

Contact resistance: 50m ohms maximum

Insulation resistance: 50m ohms minimum

Contact pressure: 0.5N(50gf) minutes

Insertion force: 3-30N(0.3-3.0kgf)

Withdrawal force: 3-30N(0.3-3.0kgf)

Phone Jack with DC 12V and 1A Rated Power

2008-12-10 14:08:22

]]>

Electrical characteristics:

Rated power: DC 12V, 1A
Contact resistance: measurement shall be made at with small current 1000Hz(1A maximum)
Insulation resistance: a voltage of 500V DC shall be applied for 1 minute after which measurement shall be made
Dielectric strength: 500V AC(50Hz-60Hz) for 1 minute
Trip current: 2mA

Endurance characteristics:

Soldering heat test: the terminal for a printed circuit board
Temperature of solder: 260+/-
Dip time: 5±1 seconds

The terminal for a lead wire:

Temperature of solder: 350±10
Dip time: 3±1 seconds

Cold: the jack shall be stored for 96 hours at a temperature of -25±3 immediately after which measurement shall be made

Dry heat: the jack shall be stored for 96 hours at a temperature of 70±2 immediately after which measurement shall be made

Contact resistance: 50m ohms maximum

Insulation resistance: 50m ohms minimum

Contact pressure: 0.5N(50gf) minutes

Insertion force: 3-30N(0.3-3.0kgf)

Withdrawal force: 3-30N(0.3-3.0kgf)

Tact/Micro Switch with 3Kgf Stem Strength and 0.3 ±0.1mm Travel

2008-12-10 10:52:37

]]>

Actuating force: 100 to 260 ±30gf

Travel: 0.3 ±0.1mm

Stem strength: 3Kgf

Contact resistance: 50m ohms maximum

Insulation resistance: 100m ohms maximum

Dielectric withstanding: there shall be no breakdown

Operating temperature range: -20 to 70 degrees Celsius (normal humidity, normal press)

Storage temperature range: -20 to 80 degrees Celsius (normal humidity, normal press)

Scope: specification covers the requirements for single key switches which have no key top (tact switches, mechanical contact)

Precision Potentiometer with Nominal Resistance Range of 10 Ohms to 20M Ohms

2008-12-10 11:13:09

]]>Characteristics:

Range of nominal resistance: 10 Ohms to 2M Ohms
Resistance tolerance: ±10%
Terminal resistance: 1%R or 2 Ohms
Contact resistance variation: 3%R or 3 Ohms
Insulation resistance: R1≥1G Ohms
Withstand voltage: 101.3kPa/500V, 8.5kpa/315V
Effective electrical travel: 210±100
Rated maximum power working voltage: 250V +70V 0.5W +125W
Temperature range: -55 to +125 degrees Celcius
TCR: ±250ppm
Temperature variation: R≤±2%RUab/UacR≤±1%
Collision: 390m/s², 4000uqw, R≤≥1%R
Vibration: 10 to 2000Hz, 0.75mm, 98m/s2, 6h
R≤±1%RUab/Uac≤±2%
Climate category: R≤±3%RR1≥100M
Electrical endurance: 70W, 0.5W, 1,000h, R≤±3%R
Mechanical endurance: 100cycles, R≤±3%R Steady damp-heat
R≤≥3%R, R1≥100M
Total mechanical travel: 2500±100
Starting torque: ≤20mNm
Stop torque: ≥50mN?m
Standard packaging: 50 pieces per tube

Precision Potentiometer with Resistance Tolerance +/- 10%

2008-12-10 11:59:45

]]>Characteristics:

Range of nominal resistance: 10 Ohms to 2M Ohms
Resistance tolerance: ±10%
Terminal resistance: 1%R or 2 Ohms
Contact resistance variation: 3%R or 3 Ohms
Insulation resistance: R1≥1G Ohms
Withstand voltage: 101.3kPa/500V, 8.5kpa/315V
Effective electrical travel: 210±100
Rated maximum power working voltage: 250V +70V 0.5W +125W
Temperature range: -55 to +125 degrees Celcius
TCR: ±250ppm
Temperature variation: R≤±2%RUab/UacR≤±1%
Collision: 390m/s², 4000uqw, R≤≥1%R
Vibration: 10 to 2,000Hz, 0.75mm, 98m/s2, 6h
R≤±1%RUab/Uac≤±2%
Climate category: R≤±3%RR1≥100M
Electrical endurance: 70W, 0.5W, 1,000h, R≤±3%R
Mechanical endurance: 100cycles, R≤±3%R Steady damp-heat
R≤≥3%R, R1≥100M
Total mechanical travel: 2500±100
Starting torque: ≤20mNm
Stop torque: ≥50mN?m
Standard packaging: 50 pieces per tube

Precision Potentiometer with Stop Torque of ≥50mNm

2008-12-10 11:45:02

]]>Characteristics:

Range of nominal resistance: 10 Ohms to 2M Ohms
Resistance tolerance: ±10%
Terminal resistance: 1%R or 2 Ohms
Contact resistance variation: 3%R or 3 Ohms
Insulation resistance: R1≥1G Ohms
Withstand voltage: 101.3kPa/500V, 8.5kpa/315V
Effective electrical travel: 210±100
Rated maximum power working voltage: 250V +70V 0.5W +125W
Temperature range: -55 to +125 degrees Celcius
TCR: ±250ppm
Temperature variation: R≤±2%RUab/UacR≤±1%
Collision: 390m/s², 4000uqw, R≤≥1%R
Vibration: 10 to 2000Hz, 0.75mm, 98m/s2, 6h
R≤±1%RUab/Uac≤±2%
Climate category: R≤±3%RR1≥100M
Electrical endurance: 70W, 0.5W, 1,000h, R≤±3%R
Mechanical endurance: 100cycles, R≤±3%R Steady damp-heat
R≤≥3%R, R1≥100M
Total mechanical travel: 2500±100
Starting torque: ≤20mNm
Stop torque: ≥50mN?m
Standard packaging: 50 pieces per tube

Precision Potentiometer with TCR ±250ppm

2008-12-10 11:16:23

]]>Characteristics:

Range of nominal resistance: 10 Ohms to 2M Ohms
Resistance tolerance: ±10%
Terminal resistance: 1%R or 2 Ohms
Contact resistance variation: 3%R or 3 Ohms
Insulation resistance: R1≥1G Ohms
Withstand voltage: 101.3kPa/500V, 8.5kpa/315V
Effective electrical travel: 210±100
Rated maximum power working voltage: 250V +70V 0.5W +125W
Temperature range: -55 to +125 degrees Celcius
TCR: ±250ppm
Temperature variation: R≤±2%RUab/UacR≤±1%
Collision: 390m/s2,4000uqw, R≤≥1%R
Vibration: 10 - 2000Hz, 0.75mm, 98m/s2, 6h
R≤±1%RUab/Uac≤±2%
Climate category: R≤±3%RR1≥100M
Electrical endurance: 70W, 0.5W, 1000h, R≤±3%R
Mechanical endurance: 100cycles, R≤±3%R Steady damp-heat
R≤≥3%R, R1≥100M
Total mechanical travel: 2500±100
Starting torque: ≤20mNm
Stop torque: ≥50mN?m
Standard packaging: 50 pieces per tube

Precision Potentiometer, Cermet Potentiometer, Trimmer Potentiometer, Trimpots, Variable Resistor

2008-12-10 11:55:48

]]>Characteristics:

Range of nominal resistance: 10 Ohms to 2M Ohms
Resistance tolerance: ±10%
Terminal resistance: 1%R or 2 Ohms
Contact resistance variation: 3%R or 3 Ohms
Insulation resistance: R1≥1G Ohms
Withstand voltage: 101.3kPa/500V, 8.5kpa/315V
Effective electrical travel: 210±100
Rated maximum power working voltage: 250V +70V 0.5W +125W
Temperature range: -55 to +125 degrees Celcius
TCR: ±250ppm
Temperature variation: R≤±2%RUab/UacR≤±1%
Collision: 390m/s², 4000uqw, R≤≥1%R
Vibration: 10 to 2000Hz, 0.75mm, 98m/s2, 6h
R≤±1%RUab/Uac≤±2%
Climate category: R≤±3%RR1≥100M
Electrical endurance: 70W, 0.5W, 1,000h, R≤±3%R
Mechanical endurance: 100cycles, R≤±3%R Steady damp-heat
R≤≥3%R, R1≥100M
Total mechanical travel: 2500±100
Starting torque: ≤20mNm
Stop torque: ≥50mN?m
Standard packaging: 50 pieces per tube

Precision Potentiometer, Trimpots, Cermet Potentiometer, Trimmer Potentiometer, Variable Resistor

2008-12-10 11:22:33

]]>

Nominal resistance: 10 to 2M

Resistance tolerance: 10%

Terminal resistance: 1 percent or 2

Contact resistance variation: 3 percentR or 3

Insulation resistance: R1 1G

Withstand voltage: 101.3 kPa 500V, 8.5kpa315V

Effective electrical travel: 210 +- 100

Power working voltage: 250V +70 0.5W +125 0W

Temperature range: -55 to +125 degrees Celsius

TCR: 250ppm

Temperature variation: R2 percent R Uab/Uac R1 percent

Collision: 390m/s2,4000uqw, R1 percent R

Vibration: 10~2000Hz0.75mm 98m/s2

Climate category: R3 percentR R1 100M

Electrical endurance: 70 0.5W 1000h R 3R

Mechanical endurance: 100 cycles R 3R

Steady damp-heat: R3 percent R R1 100M

Physical charactiristics:

Total mechanical travel: 210 10
Starting torque: 20mNm
Stop torque: 50mNm
Standard packaging: 50pcs per tube

Precision Potentiometer, with 10 Percent Resistance Tolerance, TCR: 250ppm

2008-12-10 11:49:41

]]>

Electronical characteristics:

Range of nominal resistance: 10-2 mega Ohms
Resistance tolerance: 10 percent
Terminal resistance: 1percent R or 2 Ohms
Contact resistance variation: 3 percent R or 3 Ohms
Insulation resistance: R1 1Giga Ohms
Withstand voltage: 101.3 kPa, 500V, 8.5kpa, 315V
Effective electrical travel: 210±100

Environment characteristics:Power voltage: 250V +70 0.5W+125 0W

Temperature range: -55 - +125 degree celsius

TCR: 250ppm

Temperature variation: R 2 percentR Uab/UacR 1 percent

Collision: 390m/s2,4000uqw, R 1percentR

Vibration: 10-2,000Hz 0.75mm 98m/s26h

Climate category: R3RR1 100M

Electrical endurance: 70ohms 0.5W1000h R 3percent R

Mechanical endurance: 100 cycles R3R

Steady damp-heat

Precision Trimpots, CermetPotentiometer, Variable Resistor with Resistance Tolerance of ±10%

2008-12-10 11:24:07

]]>Characteristics:

Range of nominal resistance: 10 to 2 M Ohms
Resistance tolerance: ±10%
Terminal resistance: 1% R or 2 Ohms
Contact resistance variation: 3% R or 3 Ohms
Insulation resistance: R1≥ 1G Ohms
Withstand voltage: 101.3kPa 500V, 8.5kpa 315V
Effective electrical travel: 210±100
Rated maximum power working voltage: 250V +70V 0.5W +125W
Temperature range: -55 to +125 degree Celsius
TCR: ±250ppm
Temperature variation: R≤± 2% RUab/UacR≤ ±1%
Collision: 390m/s²,2400uqw, R≤≥1%R
Vibration: 10 to 2000Hz, 0.75mm, 98m/s², 6h
R≤± 1%RUab/Uac≤±2%
Climate category: R≤ ± 3% RR1≥ 100M
Electrical endurance: 70W, 0.5W, 1000h, R≤±3%R
Mechanical endurance: 100 cycles, R≤± 3%R steady damp-heat
R≤≥3%R, R1≥100M
Total mechanical travel: 2500±100
Starting torque: ≤20mNm
Stop torque: ≥50mN?m
Standard packaging: 50 pieces per tube

Precision/Variable Resistor with ±10% Resistance Tolerance and ≤50mNm Stop Torque

2008-12-10 11:20:22

]]>

Range of nominal resistance: 10 to 2Mohms

Resistance tolerance: ±10%

Terminal resistance: 2 ohms

Contact resistance variation: 3 ohms

Insulation resistance: R1 ≥1G ohms

Withstanding voltage: 101.3kPa, 500V and 8.5kPa, 315V

Effective electrical travel: 210 ±100 degrees

Rated power: maximum working voltage 250V, +70 degrees Celsius, 0.5W and +125 degrees Celsius

Temperature range: -55 to +125 degrees Celsius

TCR: ±250ppm/°C

Temperature variation: ΔR≤±2%, R, Δ(Uab/Uac), R≤±1%

Collision: 390m/s2, 4000uqw, ΔR≤±1%R

Vibration: 10 to 2,000Hz, 0.75mm, 98m/s2, 6h and ΔR≤±1%R, Δ(Uab/Uac) ≤±2%

Electrical endurance: 70°C, 0.5W, 1,000h ΔR≤±3%R

Mechanical endurance: 100 cycles, ΔR≤±3%R steady damp-heat and ΔR≤±3%R, R1 ≥100M ohms

Total mechanical travel: 3,600 ±10 degrees

Starting torque: ≤20N.m

Stop torque: ≥50N.m

Rotary Potentiometer with Curve Taper and 250V Maximum Working Voltage

2008-12-10 11:25:54

]]>

Resistance value and tolerance: 100 to 2.2MΩ, ±20%

Taper: curve

Maximum power rating: 0.3W at 70 degree Celsius

Maximum working voltage: 250V

Sliding noise: 5%

Residual resistance: 10 ohms, R≤1K ohms, 1%

Mechanical characteristics:

Rotation angle: 240 ±10 degrees
Rotation torque: 3 to 30mN.m
Stopper strength: ≥50mN.m

Reliability specifications:

Operating life: 30 ±10%
30 cycle resistance value: ±10％
Temperature coefficient: ±3%,70°C 5HR 3%, 70°C 5HR
Temperature coefficient: ±250m/°C

Humidity characteristic: ±5%, 40°C, 90 to 95%RH, without load ±7

Resistance to soldering heat: pass 350%, 3 seconds or 260% 10 seconds, without any poor contact

Working temperature: -40 to 125%

Terminal strength: 30N.m

Temperature cycle:

Without load: 25 to 40°C, ±5%

With load: 25 to 125 degrees Celsius, ±7%

Rotary Potentiometer with More than 100 Turns of Rotational Life

2008-12-10 11:33:45

]]>

Electrical characteristics

Total resistance: 100 ~ 1MΩ
Total resistance tolerance: ±30Ω
Ratings power: 0.1W

Resistance taper: taper B

Sliding noise: 150mV maximum

Temperature characteristics: ±15% maximum

Insulation resistance: 100MΩ, minimum at DC 100V

Maximum operating voltage: AC100V at 50 degree Celsius

Solder heat resistance: 240 ~ 280 degree Celsius for 5s or 280 ~ 300 degree Celsius for 3s

Operation torque: 40~350gf/cm

Rotation stopper strength: 0.5kgf/cm/min

Total rotational angle: 260±10°

Endurance characteristics

Rotational life: more than 100 turns

Rotary Potentiometer with Withstand Voltage of 101.3kPa/500V, 8.5kpa/315V

2008-12-10 11:18:28

]]>Characteristics:

Range of nominal resistance: 10 Ohms to 2M Ohms
Resistance tolerance: ±10%
Terminal resistance: 1%R or 2 Ohms
Contact resistance variation: 3%R or 3 Ohms
Insulation resistance: R1≥1G Ohms
Withstand voltage: 101.3kPa/500V, 8.5kpa/315V
Effective electrical travel: 210±100
Rated maximum power working voltage: 250V +70V 0.5W +125W
Temperature range: -55 to +125 degrees Celcius
TCR: ±250ppm
Temperature variation: R≤±2%RUab/UacR≤±1%
Collision: 390m/s², 4000uqw, R≤≥1%R
Vibration: 10 to 2000Hz, 0.75mm, 98m/s2, 6h
R≤±1%RUab/Uac≤±2%
Climate category: R≤±3%RR1≥100M
Electrical endurance: 70W, 0.5W, 1,000h, R≤±3%R
Mechanical endurance: 100cycles, R≤±3%R Steady damp-heat
R≤≥3%R, R1≥100M
Total mechanical travel: 2500±100
Starting torque: ≤20mNm
Stop torque: ≥50mN?m
Standard packaging: 50 pieces per tube

Rotary Potentiometer, Resistance Taper: Linear (B)

2008-12-10 11:40:26

]]>

Mechanical characteristic

Total rotation angle: 230 ± 10deg
Rotation torque: 40-250GF.CM
Stopper strength: ≥1 kgf.cm

Electrical characteristic

Total resistance range: 100-2mOhm
Total resistance tolerance: 500Ohm＜R＜1MOhm, ±20%, other：±30%
Resistance taper: linear (B)
Power rating (70deg. C): 0.1W
Max. operation voltage: 100 VDC
Rotaion noise: ≤100MV
Residual resistance: ≤1％ or 100Ohm Max

Endurance

Rotation life: 100 cycles R＜10% R
Temperature: 20-70deg. C R＜±8%R

Moisture: 40deg.C 95% 5 hours(R/R) R≤±15％

Load: 40deg. C 95% 5 hours (R/R) R≤±15%

Soldering heat: soldering should be carried out within 3 seconds at a temperature of 270℃ max

Trimmer Potentiometer with Linear Taper Resistance

2008-12-10 11:30:13

]]>

Mechanical characteristic
- Total rotational angle: 200 +/- 20 degrees
- Rotational torque: 60-150gf.Cm
- Stopper strength: 500g.Cm minimum
Electrical characteristic
- Total resistance range: 100 - 2.2mΩ
- Resistance taper: linear (b)
- Power rating: ≤0.1W
- Maximum operating voltage: 50V DC
Soldering heat characteristic: soldering should be carried out within 2sec a maximum temperature of 250 degree Celsius

Trimmer Potentiometer, with 200 +/- 20 Deg Total Rotational Angle

2008-12-10 11:27:30

]]>

Mechanical characteristic

Total rotational angle: 200 +/- 20deg
Rotational torque: 60-150gf. Cm
Stopper strength: 500g. Cm minimum

Electrical characteristic

Total resistance range: 100w-2.2mw
Resistance taper: Linear (b)
Power rating(70'c): ≤ 0.1w
Soldering heat characteristic: Soldering should be carried out within 2 seconds at a temperature of 250deg. C max

Trimmer Resistor with Linear Taper and 260°±10° Total Rotational Angle

2008-12-10 11:08:43

]]>

Mechanical characteristics:

Total rotational angle: 260°±10°
Rotational torque: 40 to 250 gf.cm
Stopper strength: ≥1kgf.cm

Electrical characteristics:

Total resistance range: 100Ω to 4.7MΩ
Total resistance tolerance: 500Ω1MΩ: ±20%, other: ±30%
Resistance taper: linear (B)
Power rating (at 70°C): ≤0.25W
Maximum operating voltage: 250V AC
Residual resistance: R<10kΩ: 10Ω (maximum) 10kΩ: 3% (minimum)

Endurance:

Rotation life: 500 to 10,000 cycles
Temperature characteristic: 20 to 70°ΔR<±8%R
Moisture characteristic: 40°C 95% 5 hoursΔ(R/R) R≤±15%
Load characteristic: 40°C 95% 5 hoursΔ(R/R) R≤±15%
Soldering heat characteristic: 270°C (maximum) at 3 seconds